Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Hi,
I have a ble device that uses nRF52 chip. I would like to know if it is possible to do ble automation on that device.
Here is my setup:
OS: Ubuntu 20.04 LTS
...
Hi everyone, I am using TWI driver to communicate with I2C. I have write the following I2C read function.
Now I want to write a second I2C function with some modifications...
Hi,
I have a device that throughout the uart data to ble,recently I find a problem that in the case of weak signals,the data sequence is out of order.
Here is the question...
Hi,
I am trying to run the sensor example as provided in the Mesh SDK. I am getting the log as mentioned:
13691970>, main.c, 475, mocked motion sensed = 0% <t: 13691973...
Hi there,
I'm using the softdevice sd_ecb_block_encrypt to encrypt my 16byte block data as follows:
When my data buffer is filled, it called aes_encrypt(),
void aes_encrypt...
Hi Nordic,
I are working on battery operated device.
Need to measure battery percentage using ADC.
Let me know how can we select range of 0-100% for battery voltage...
Hello,
How do you flash custom firmware into the Nordic Thingy 52? The Thingy doesn’t reflect changes that I make to the firmware files and instead just turns off the...
I'm trying to find an example of how to properly buffer sensor readings between connections, and then transmitting the buffer on connection.
Is this just done via the user...
Hi,
I have developed a piece of software that only uses the GPIOs on the APP core to evaluate a sensor. The software worked on the development board processor so I made...
Hi support team,
In my case, i want to auto disconnect to ble central after some minutes with no message transfered, so i create an timmer and set event compare and clear...
We are developing a beacon with nrf52810. We test ble_app_beacon example and a modified example( the difference is, advertising packets are connectable to be applicable in...
I've configured UART2 on the nRF9160 to connect to a nRF52840. The nRF52840 generates a payload and sends it over to the nRF91. The payload size during testing was 65 bytes...
Hello,
I am developing using nrf2840 PDK, SDK v17.0.0, S140
I have made two services, one is to control the led blinking rate via nrf connect android app and the other...
Hi,
Is it possible to have dual transport for DFU (UART and OTA)?
I read this in the forum: https://devzone.nordicsemi.com/f/nordic-q-a/28118/multiple-dfu-transports ...
