I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hi, I'm trying to run the nfc_pairing example from the master branch (1.3.99) of NCS. I've successfully built the example in SES and loaded it onto my nRF52840DK, but the...
I'm wondering how BLE signals are handled at the layer below the scanning module. Namely, suppose there are hundreds of BLE modules that are all advertising nearby. How does...
Hi
We are developing a 70 x 70mm PCB containing a nRF52840 for BLE/ESB and a second module for WiFi/BT.
We have no mechanism to avoid transmission of the WiFi module while...
Hi. Sorry, can't find the answer on the forum on my problem.
I am using:
nRF52840 DK
Segger
MacOS
Fanstel BC840 module
I have a project that flashes to Raytac...
Are there any examples of how to enable and use coded phy long range with the nRF Connect SDK? I have the nrf52840DK and would like to create an advertising example to test...
Hello,
In my current project designed around nRF52840 incorporating many peripherals (limited power budget) and many central devices. Each peripheral can connect to any...
Hi
I am using NRF52810 with Softdevice S112 7.0.1 and SDK 16
I want to ask about the behavior of the softdevice notification queue on disconnect. I have seen these two...
Hi .thank u for reading this .First sorry for my english. This is the story:
I try to make a flexible mesh using multi nrf24l01+ more than 10 nodes. I searched so many topic...
While running a Scan in nRFConnect 4.24.3 on Android 10, Nokia 6.2, I see the first Advertisement from my BLE Device. That device advertises different sets of ScanData over...
Hi ,
I am working on a project where i need to publish wifi scans over ble , issue is that when ever we try to send data over it either send or not sent to avoid data loss...
Does Nordic have some solution for this? Device would be a WiFi+BLE gateway, which runs Linux, and can support advertising scan for at least 300 beacons, and have Ethernet...
Hi, I am running into issues where the nRF9160 (in NB-IoT mode) does not seem to handle cell changes reliably. I am using modem firmware mfw_nrf9160_1.2.0 . I made a simplified...
Hi Nordic guys,
I'm trying to create a pin pairing between an NRF52 DK and iPhone.
I've created this function to do that:
I've added that function in the ble_peripherical...
Hey! I am using nRF52 DK, SDK 15.2.0, and softdevice s112. I have an application that reads some data with the saadc, advertises, sends data if a connection is made or stores...
