[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
Hi,
we've just found the information about the knobattack ( https://knobattack.com/ ).
Is there any fix for this issue with the new updates?
Best regards,
Constan...
Hi,
I have recently developed a simple custom board with the use of the BL651 module to have a dev board for myself. Although the schematic diagram is simple and the PCB...
I have nRF9160-DK bought fairly recently. The IMEI is printed on a label on the back of the board. But, there is not PIN. Registering the board as an LTE device on nrfCloud...
Hey all,
I was curious to see if anyone else is seeing the same problems I have with DFU.
I'm currently running SDK 15.2 and version 1.8.8 of nRF Connect on iOS. When...
Hello,
Previously I was using nRF52 SDK V11, printf did print properly and provided linefeed with '\r\n'.
Now I started using SDK V15, printf is no longer supported and...
I'm developing a nRF52832 based HID device and I'm at a bit of a loss as to why it isn't working on iOS. The device works as a keyboard fine on macOS, and it connects and...
Running nrfjprog 10.3.0 on macOS 10.14.6 (18G87) with an nRF52 dev kit
Occurs on all 10.x releases of Nordic command line tools. Other switches such as -i work.
edit...
Hi, I installed the nRF connect SDK, but get the following problem when trying to open the asset tracker project:
If I press ok, I see this:
Any ideas about what...
I use nrf52832.
Document written,
-------------------------------------------------------------------- RX current comsumption is IRADIO_RX0 Radio RX@1Mb/s BluetoothLowEnergymode...
Hello,
I'm trying to use raspberry pi to program nRF52832 on mass production. Because it's easy to do some test job with raspberry pi.
But there are still some issue I...
I want to achieve: 1. Mobile application networking with multi-lamp mesh 2. After mesh networking, many smartphones control all lights independently through proxy nodes. I...
Hi,
We are using nRF52832 based module on which we are using HCI over UART functionality with the help of Zephyr(v1.14.0) SDK to find the nearby beacons via Bluez stack...
Hello there,
So we are working with a sensor that needs to receive a pulsed voltage, so we are using a PWM signal from our nrf51-DK applied to a transistor based circuit...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the nRF5 SDK v15.3.0 and modified twi_sensor_pca10056 program...
