I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
I'm building a system with onboard stereo speakers that can take a maximum of 1,4A when operating at low battery voltage. Can I safely bypass the npm1300 and directly draw...
I am using nRF Connect SDK 2.9.0 with Toolchain 2.9.0 and trying to interface Winbond W25Q32 SPI flash memory with nRF21540DK (nRF52840) . I need help with the following:...
I use SDKv2 . 09 . 00 without using the eSB function timelot can trigger MPSL_TIMESLOT_SIGNAL_TIMER0 normally，then NRF54L15 Running esb and BT at the same time with MSPL cannot...
Dear Sir / Madam,
We are testing with NRF9160 and building on top of k _uptime _ticks, I find the precision of the ticks clock to be ~70 ppm, while testing on my desk. According...
Hello,
I have been trying to figure out how to enable coexistence between Bluetooth low energy and the nRF7002 and I have some questions.
1. In the nRF Connect SDK documentation...
Using nrf5340dk, SDK v1.9.0
Want to add external RTC via I2C to wake mcu up via alarm, Facing Issue with I2C init.
I have gone through the suggested sdk fundamental course...
Hi,
When do you plan to update your Online Power Profiler Tool for cellular with nRF9151 device?
I just can see nRF9160 available for calculation.
Regards,
Hello,
I am working on an ESB (Enhanced ShockBurst) communication setup using the following hardware:
Receiver (RX): nRF5340
Transmitter (TX): nRF52840 MDK Dongle...
I am trying to compile hci_lpuart for thingy91_nrf52840, but I have these issue. hci_lpuart:
Any ideas on how to solve this? I'd really appreciate it. And if you have any...
I would like to add smp ota firmware upgrade to the matter sample project, can you provide me with the specific steps to do so, and in which path is the ota file compiled...
Good night,
I installed the VS Code/nrf Connect in my Windows 11 Prof.
I copied the "blink sample" and I tried to build it, but I am receiving
* Executing task...
I am following this example https://github.com/crfosse/ncs_projects/tree/main/peripheral_zephyr , both secure and non secure and I am not being able of making the non secure...
Hi,
I am using Mesh of 30 nodes with avg Current Consumption 6mA and 2mA in sleep mode(by calling k_sleeps) , timer is 1s timer is running to keep Real Time incremented...
Hi. I used nRF Connect SDK v2.9.1 to add OTA to the Peripheral UART sample application. The target is nRF54L10, but when I build it, the flash usage exceeds 50%.
If the...
Hi
I see i get a cmake warning with DFU enabled with the following message:
whats the purpose of this? should i just have it always enabled in my conf, or for prod...
