Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hi I have central device which has array of MAC address to connect.
when i see the structure of sd_ble_gap_connect() i cannot pass a uint8_t addr[5] as input.
so i tried...
SDK v11.0 & NRF51822 QFAC
I encountered a problem. In the process of pstorage processing flash data, a serial port interrupt came in, resulting in a system reset.
I used...
Hi,
I have discovered a (rare) problem where the S132 stack get stuck in connected state when it is not actually connected anymore.
This behavior was first reported by...
Hi,
SDK - nRF5_SDK_15.2.0_9412b96
HW - nRF52840 connectivity chip, other controller for application chip
We are tried to port serialization application on other than...
HW - nRF52840
SDK - nRF5_SDK_15.2.0_9412b96
We are running connectivity example in nRF52840 and connected UART with serialization application over UART which is different...
First proof-of-concept super-simple nRF51 board. When we load software onto this board, will we have to tailor or configure the software to bypass or disable any functionality...
Our application is similar to a wireless keyboard. The events are very sparse but we need low latency (~50ms). If I understood correctly, BLE is a synchronous protocol, meaning...
Hi I am working on nRF52832 using SDK15.02 i have below query:
During discovery I am connecting each device which is advertising and then discover for services offered by...
hi,
i am doing a project where i am using nrf52810 SOC which acts as ble shield for out customer.
customer's master device also has wifi connectivity.
the nrf52810 will...
Hi,
I had a meeting with one of our customers and was asked if any of Nordic products support ToF. I briefly looked through DevZone and found that it was not supported....
I have problem with BLE connection being constantly disconnected after 30 seconds. It is always disconnected by central device. It doesn't matter if it is iOS, Android or...
Hello,
I`m trying to run the example in the light_switch after i download the "nrf5SDKforMeshv310src"
When I tried to build Provisioner or Client ,for example this project...
Dears,
I have nRF9160-DK and nRF51-DK(PCA10028).
I have used nRFgo Studio with nRF51-DK(PCA10028) to firmware download.
And I have used nRF Connect - Bluetooth Low...
Hi.
How could I set extended advertising through the 37 secondary channels as default, in an nRF52840 module which is using PHY_CODED modulation and running a ble_app_uart...
