SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Hi, we are considering the nrf52810 for an upcoming project Unfortunately, the small flash size of 192 kB seems to be a limiting factor. The S112 softdevice and bootloader...
Hi,
currently I am adding DFU support to our application, I got everything working now, but only with the debug version of the bootloader (SDK15).
If I compile the normal...
Hi, maybe my question is a little basic, but this is my first time developing with a Nordic chip, i have been reading how to debug a nrf52 based device, and i know that i...
Hi,
I am using a central example to scan the peripheral and connects to it. I get data through notifications in bulk. That works fine. Then in order to add support to FONA808...
Hi,
I want to implement an MQTT-SN network with a Raspberry Pi 3B+ MQTT/MQTT-SN transparent gateway and some End-Devices in MQTT-SN.
This is working over Wifi with Paho...
Hi all. In my application i use display. So i need to store many fonts and images, because of that there not a lot of free memory left.
In which cases usage of mem_manager...
Hello,
I'm currently trying to connect Dongle nrf52840 to a Raspberry as a NCP. My issue is during flashing, I got a LIBUSB error when I flash the ncp usb_bootloader example...
Hi!
I have a problem with UART. SDK15. S132 6.0, nRF52832
I added UART to my project and watching strange behavior: when I attempt to send anything to UART
project...
Dear Nordic Tech Support and Developers,
Hello. I have implemented the Mesh Demo (light switch example) with Nordic Thingy 52. I would like to inquire an info on the side...
I'm using SDK12 and SES.
I compiled my code based on ble_app_uart example for nRF51822_QFAA and I see in Memory usage that RAM is at correct addresses (finishes at 0x20003FFF...
hi...
i am working on mesh , i have done light switch example , now i want to get some message from node and send to particular node . how to print the same message which...
Since the Mini 2MP is obsolete
Via this link https://www.amazon.com/Arducam-Module-Megapixels-Arduino-Mega2560/dp/B012UXNDOY only can buy Mini-2MP-Plus
The official git...
Hi,
I am using 2 gpio interrupts from 2 separate sensors with active soft device. one sensor generates interrupts at around 400-800 ms and the other comparatively lesser...
Hi,
So I am trying to poll the signal strength of the nRF9160 DK and at first everything seems okay, the device gains connection and all the boxes in the LTE Link Monitor...
