Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Is there a plan to fix this errata limitation from errata limitations documented on softdevice?
If Radio Notifications are enabled, flash write and flash erase operations...
Hi all,
I'am using nfc url record from nRF5_SDK_11.0.0-2.alpha.
The example works fine on PCA10036 but not PCA10040.
No ITs are generated on µC.
I'am using Nexus 5X...
I am developing an code which requires use of multiple Timers.
I am using Sdk 11 here when i try to initialize timer there is no field for APP_TIMER_MAX_TIMERS in APP_TIMER_INIT...
Inorder to create a c++ wrapper in nordic SDK , i have to
change the Makefile so that it can compile both C++ and C.
in the example the makefile already has gcc added but...
I would like to have BLE using 51822 and audio using a separate BT classic chip on my device. Are there any products in the market that use separate BT chips for LE and classic...
Hello everyone,
I would like to ask that when my project will get the event(BSP_EVENT_SLEEP、BSP_EVENT_DISCONNECT and BSP_EVENT_WHITELIST_OFF)
With the example,in the...
Hi,
I am evaluating the NRF52 with PCA10040 board and nRF5x_SDK_11.0.0.alpha.
I want to create Wave Forme as below.
Out[0] pin transit low to high at compare 0, Out...
I noticed S110 is not listed as supported by nRF5 SDK11. However, no supported SoftDevice seems to offer the same functionality as the S110 (Peripheral only protocol stack...
Hi,
in SDK v9, i tried to compile the bootloader example, but:
/usr/lib/gcc/arm-none-eabi/5.3.0/../../../../arm-none-eabi/bin/ld: region `FLASH' overflowed by 6944 bytes...
Did anybody know how I could determine the connection interval for a established ble connection between an android (4.4) central and a (e.g. nRF51822) peripheral?
I've been having a little bit of an issue trying to parse UART data that I am receiving from an external device.
Where I'm having issues right now is comparing an incoming...
Every 10 packets send; it will have at least 1 packet with 1-2 bytes corrupted data.
The configuration as below:
data rate: 2Mbps
channel: 7
Prefix0: 0xE2
BASE0...
Hi,
We have an application that can run in two modes. The mode is selected by setting the GPREGRET to 1 or 0 and restarting.
Currently we are running this procedure directly...
