SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
is there a way to get more control over the auto ack feature of the 802.15.4 driver in zephyr?
I would like to ack frames without destination address only if nrf_802154_ack_data_pending_bit_should_be_set...
Hi all:
I have a software version that allows Bluetooth to be connected to the phone normally,
When I tried to use the SPI interface, it happened as long as I used
...
Hi there,
I'm trying to wire up a Uarte client to a Uarte server where the client device is an nRF9160DK, and the server is an nRF52840DK.
Connectivity between the cilent...
Hello,
My hardware guy asked me to look into whether or not we can use a fixed eSim (no card) with the 9160? If this is possible how do we program it with the particular...
Hi,
GOAL : I try to measure the current consumption in system off only.
PROBLEM : I measure a current of 8uA in system off while in the datasheet of the PAN1781 et nrf52820...
Hi, I accidentally marked one of my own replies as the answer.
I'm trying to interface LR1110 (Dev Board) with NRF9160 DK using SPI. I have been working on this for a couple...
Hello,
I am looking for an example that have the the ccs811 on the sdk15 but i didnt find it , I have found some driver ext like ccs811.h on the driver_ext file but I dont...
Working on a zephyr/zigbee/802.15.4 system and my code (loosely based on the Nordic samples) on a custom device was not behaving as expected.
So I broke out an nRF5340 DK...
Hello Devzone,
I'm writing to ask about how long a device running Nordic's aws_iot sample app (sdk-nrf 1.6.1 based, Zephyr 2.6.0 based) may be in a "radio idle" state, and...
I'm using an application based on the MQTT_CLIENT example. Without any change, it worked fine.
Now I tried to add UART2 as a communication channel to another controller...
Hi Community,
I am using ble_hrs_heart_rate_measurement_send API to send notifications to my central device which is a android mobile.
Recently I have observed packet...
Hi,
How are you?
Could help someone with a ask?
I am designing a plate and I am using like guia the nRF9160 DK. The Layer Stack Manager has configured the Top Layer...
path:
\experimental\cli\cli_agent_router\pca10059\mbr
When I execute "bdb start" in the serial port and then execute "bdb Legacy Enable", the terminal devices that are...
