I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
In the documentation for the secure bootloader, it's mentioned that the provisioning data gets stored in OTP memory for some chips (e.g. nRF5340). Is there a way to know what...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Hi -
I'd like to set the i2c to clock in at no more than 2 khz. Are there FREQUENCY register settings that would work for this. In addition, is there a reference as to how...
Hello, I am a beginner to nRF54 series (currently have nRF54L15DK) and to understand the concepts and communication between nRF devices and iOS software with bluetooth LE...
Hello,
On nRF52832, I implemented a code with PWM output at P0.07.
Here is the section at my overlay:
pwmleds {
compatible = "pwm-leds" ;
pwm_led0: pwm_led_0 ...
Hi, We want to integrate LORA LR1110 for the final year capstone project. From the documentation we have understood that Kit is fully compactable with Arduino UNO. But SPI...
Hi. I am trying to control a RC servo with a nRF52810 MCU (in short, a servo needs pulses in range of 1000-2000us once every 20ms to move to specific position. Minimal change...
Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Hey folks, we are planning to implement BLE Audio based on one of the Nordic ships and unfortunately nrf54H is not really available now and nrf54l does not support LC3 audio...
I'm encountering a blocking issue when trying to create a new board using the NCS Board Wizard in VS Code with Nordic Connect SDK v3.0.0. After filling in valid inputs and...
Hi,
After some difficulty in obtaining the modem trace file, I'm here to have help about connectivity issue. I have a custom board build with an nRF9151, I use Onomondo...
Hi There,
I am using a nRF52840DK board to experiment with NFC Tag technology.
I started with the "Writable_ndef" example inside the nRFConnect, and it works.
I wrote...
Dear staff,
Im new to Nordic chip so please forgive us
We bought 2 nrf52833DK and we started by following your tutorial on vscode ( nRF Connect for VS Code - Tutorials...
When we define a CMake presets file in an application folder and try to load a preset from it in the "Add Build configuration" tab created by the nRF Connect Extension for...
I am using nRF Connect SDK v2.4.0 and an nRF5340 DK set up as a PAwR advertiser. Is it possible to specify the channels to use in the Periodic Advertising train? I found the...
