Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
I have this as nrf52840dk_nrf52840.overlay in my application directory:
/ {
lightStrings {
compatible = "gpio" ;
lightString0: lightString_0 {
gpios = <& gpio0...
Dear Sirs!
I am going to use nrf_drv_spi_xfer to read 15 bytes periodically (Approximately each 4 ms) according to GPIO (GPIOTE Event via PPI). To do it I am going to call...
I'm attempting to use a vendor or custom model to deliver sensor data through a ble mesh using a nrf52840dk board. On Ubuntu, I'm using the nrf connect sdk v2.2.0. i have...
Hi,
We are using the nordic sdk 1.9.1.
I have created my own project and i want whole sdk commit to my repo. I am able to build the project. I am not able to commit the...
Hello Guys,
I am trying to implement our own firmware update over ble in Mobile App.
The whole process is succesfully done by Nordic Application (Device Manager).
I...
Hi,
I'm implementing a circuit that uses both ble and usb communication using nRF52840.
I'm configuring power source and i'll configure schematic like reference circuit...
Hi there.
I am currently developing a simple asset tracker based on several examples using nrf9160 custom board.
So I am using several examples like mqtt_simple, gnss...
Hi,
I am using STLED524 intelligent matrix LED display driver IC for my project.I need to interface STLED524 with nRF 52 board.I am checking for driver library for it.But...
Dear All,
I'm implementing a SNTP sync over Ethernet and found the following issues:
1- CONFIG_DATE_TIME_AUTO_UPDATE must be disabled to get a NTP time sync scheduling...
It seems like there are lots of questions regarding simple GPIOs and devicetree, but I can't quite find something that describes my problem:
I am using the nrf52840dk...
Hi,
Our team is developing an application based on the nRF5340-DK - we are developing on the DK while our hardware is in transit. Our schematic largely follows the reference...
I have developed a thread network using nRF52840 dongle and Raspberry Pi 4B. I have checked from the command line of the RPi, the transmit power is 0dBm. Can you please confirm...
Hi,
I use embedded wizard tool to handle display graphic and I need allocate a RAM buffer for it. I need to write frame buffer ram start and size in embedded wizard config...
Hi all,
I want to compile chip-tool so that I can make 5340 into a matter network. But I always fail to compile.
environment:
raspberry pi 4B + ubuntu-22.04.1-preinstalled...
