Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I tried to upgrade the modem firmware on NRF9160-DK to the latest 1.3.0, downloaded from https://www.nordicsemi.com/Products/nRF9160/Download#infotabs .
After (succesfull...
Hi,
We are using SDK 14.2 with s132 v5.1.0. Reviewing the changelog for newer versions of the SoftDevice, we see:
"A memory access fault (NRF_FAULT_ID_APP_MEMACC) can...
Hello,
I am developing a device with a nrf52 using s140 with the last sdk. The objective is to interact through ble with other devices that have different custom services...
I'm porting a bluetooth app developed on a PCA10040 to a prototype PCB with a Fanstel BT840F.
My development environment is
Windows 10
nRF Connect V3.7.1
Toolchain...
Hi I have create a firmware to exchange sensor data through UART / RS485 (MODBUS Slave).
I succeeded to create my firmware and test it with a USD Serial to RS485 device...
Running lwM2M_client routine into PSM with nRF9160 is about 450uA current， RTT is used for logging and all UART is disable.
I use ncs1.6.0.
What's causing 450ua?
How...
dear simon
First of all, thank you very much for your help，Now in my program, I also encountered such a problem，I use NRF_ qspi_ Nor the power consumption of my whole system...
Hi
I configure two IO output PWM, one of which outputs PWM all the time, and the other turns on PWM by timer intermittently ，The period of the former becomes wider，As shown...
I’m not able to connect my Thingy91 to the network. I have successfully registered my Ibasis SIM card in the nRF Cloud (or at least that is what I think I have done):
...
Hi,
I am trying to configure a basic output pin in the device tree configuration. I read somewhere a 'compatible' parameter is requires because it describes what will be...
hi team,
Intial we followed this link for system on --> https://embeddedcentric.com/lesson-14-nrf5x-power-management-tutorial/
Now we are trying to enable the constant...
Hai
I have an NRF52840 Development board with 1MB of flash. I have an requirement to store a large amount of data in a flash around 6k samples in one record.
For this...
Hello,
Im using E73-2G4M08S1C module based on nrf52840. Somehow even when in erased state its consuming a lot of energy and starts heating very fast.
Im trying to figure...
Hi Nordic team
I failed to demostarte multicell location sample.
Hardware: Thingy91
SDK: v1.6.0/multicell location
Modem: v1.3.0
Q1. At prj.conf, nrf cloud location...
Hi Nordic
We are developing our IOT product and we are starting our development of firmware on nRF9160 DK so that we can port that code to our custom PCB that will contain...
