SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Hi
I found a strange issue on nrf52832. And I use nRF5-SDK-v13.1.0 .
When I assignment P0.7->SCL & P0.6->SDA, the twi function not working. But I change the assignment...
Today I read about the new nrf52810 and I want to know about its main differences with the nrf52832.
I see a lower power consumption for the 52810 vs 52832 and no NFC on...
Hi
Currently I try to migrate my software project (with SDK14.2, S132 (5.0.0), arm-gcc toolchain ) from nRF52832 to nRF52810 (with SDK14.2, S112 (5.1.0), arm-gcc toolchain...
Hello everyone, I am a beginner in the use of Nordic Thingy: 52. I would like some help trying to reprogram the Nordic Thingy module. After a programming error of the Thingy...
HI,
I am unable to communicate between a SDK 8.0 based nRF51822 sender and SDK 14 based NRF52832 receiver.
The data rate of the SDK 8.0 sender is 250 KBits/sec, whereas...
Hi,
Can someone help me with question on SPI?
What is the difference between SPIM and SPI? They seem to have different clocks
Also in the SPIM section, the frequency...
Hi there,
I am developing a BLE dongle on nrf51822. There is no external 32.768KHz crystal oscillator on my customized board(only has an external 16MHz oscillator)....
hi,
I need to know how to use "power on reset". From the reference document, I can understand BOR and POFWARN. But the POWER ON RESET, I could not get any idea.
1. POR...
i have project with nRf51822 and uart. i use uart fifo in Uart_app_ble example sdk11. now i need disable or enable Rx, TX.i tried this function :
NRF_UART0->TASKS_STARTRX...
Hi,
Has anyone successfully used semaphores/mutex implementations of FreeRTOS?
The code I am working on is based on the FreeRTOS HRS SDK example. I am looking to add a...
Trying to compile using the on-line Mbed compiler. I keep getting cannot find "nrf.perhiperals.h", and I cannot locate it either.
Possible someone can point me in the right...
Hello.
I'm using Tielen Marjle STM32 library for nrf24l01+ ( https://stm32f4-discovery.net/2014/06/library-17-nrf24l01-stm32f4xx/ ) which worked great till now, when I...
This is related to the new nordic dev zone, not nrf connect, but there is no dropdown option for it.
After signing into the new nordic dev zone for the first time since...
Hi there,
I'm using ASUS RT-AC1900P router with IPv6 DHCPv6 on. RPi gest its own IP with prefix specified in router but interface wpan0 (wpantund) not. I have configured...
