Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
I'm on windows 8 using the 1.0.1 sniffer application and wire shark 1.10.14 64bit with a Nordic nrf51 dongle. I'm using an nrf51 dev board with ble_peripherals/ble_app_blinky...
with nrf51 there is 2 blocks (block0 for softdevcie and block1 for user data and stack). I configured the system to retain RAM before going down using sd_power_ramon_set(0x00030003...
Hi,
I have a device that is configured to work in GAP central role. This device only scans for specific advertisements from specific devices. Could you suggest how I can...
Hi!
I used the develop board test the application "ble_app_multilink_central" and "ble_app_multilink_peripheral",but it is always connected failed,and disconnect Reason 0x0008...
Hi there. I have a very long C code that is running correctly on Code:Blocks, Ubuntu Terminal ( using GCC ), Eclipse and on Dev-C++.
However, when I put in on the board...
Hello,
I've been trying to control MCP23017 IO expander with TWI using nRF52832. When I execute the code it stops at nrf_drv_twi_tx. The address pins A(0:2) are 0.
Any...
I have having following configuration:
I want a fail safe method to update firmware on nrf51822 using attached host controller. I looked at serial wire debug interface...
Hello,
I'm running a serialized application based on the SDK 10 and S130 v1 and I am in the process of porting the peer manager to the application µC.
Due to the fact...
I'm trying to set up a system where the sample rate of data being notified to the client from various sensors can be changed by updating a configuration characteristic in...
Hi all,
I have one nRF52 DK board (PCA10040), and I have installed necessary JLINK drivers when first connecting the board to PC, it can displays the virtual COM port correctly...
I have a board here with nrf52832 rev B attached to a max98089 i2s codec. In this application we are only really using the ADC channel of the codec. Everything is configured...
Hi NordicS
Do you have a code example for a central UART application?
I am looking for a example that acts just like the nRF Uart App, but running on e.g. a PCA10031...
Is there a way to resolve a private resolvable address on connection? I have all the bonding information, IRKs etc, from everything which I'm bonded with, I'd like to work...
Hi.
I'm currently trying to scan beacons with timeslot example.
However, I found that there're more than 20% of loss while scanning beacons broadcast.
I think that...
