Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
I am trying to use the Serial Modem Add-On (SM) application with the attached overlay-external-mcu.overlay. When DTR is asserted (active low), the modem stops responding to...
I would like to know the Host subsystem DN/QDID of nRF Connect SDK 3.2.0 for nRF52832. It is not described below. docs.nordicsemi.com/.../ble_qdid_qual_matrix.html
I am working with the nRF54L15 to create a driver for a peripheral which is controlled by two PWM signals.
My driver relies on the Zephyr PWM driver which goes back to your...
HI
How much current dose the individual GPIO pin source/sink for nRF5340 as in the datasheet V1.3 it is mentioned "Added guidance on maximum combined GPIO sink/source current...
Hello,
we want to setup an environment for automated testing of our bluetooth mesh system.
The test system should be able to provision and communicate over a device that...
Hi
If my calculations are correct the NORDIC whitepaper WP008 on PRINTED MONOPOLE ANTENNA for 2.45Ghz the quarter wave length antenna trace is not 92mm
For TOP layer PCB...
Hi,
I was trying to get the NFC Sample programs to work on the nRF52840 DK but the NFC tag is not being read by my phone. The program itself is running (confimed through...
I am working on a school project and need to set up SPI communication between a wiznet,W5500 and the nRF54L15DK. I can build and run my program but I am getting no responce...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hello,
With NCS v 3.2.1, I am working on a BLE application with nRF52840 dongle.
I was trying to add FOTA feature in my application by adding the following line to sysbuild...
I just ordered and opened up the nRF9160 dev kit from Digikey. I was going through the quick start and I named the device and when I went through the verification step, it...
Can you clarify, is it possible for the nPM2100 to set Vout < Vbat I.e. 1.8v out with 3v battery? The behaviour of the EV kit suggests not...
The datasheet isn't really...
We have a Thingy:91 (nRF9160) that we use for various LTE-M / NB-IoT network debugging. Until recently I was able to see both RRC and NAS messages in both " Cellular Monitor...
Hello,
I am developping an application based on ESB protocole using BT840NE module (nrf52840 + nRF21540) SDK 3.2.0.
on the PTX side, I am measuring the current using the...
