Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi Nordic,
I have learned about both the DTM and radio_test example source code. For our prototype tests, I think the latter may be better for us.
I have tried to wirte...
Hi
Is there a possibility to update the bootloader himself over the BLE DFU?
I have a new bootloader with a bigger size (MemoryMap changed) and I am wondering if I can...
Hello,
The following error message appears when the original code "asset_tracker_v2" under NCS 2.0 is compiled with vs code IDE,
Can anyone give me some comments? Thanks...
Hello,
I'm just trying to run the LTE_BLE_GATEWAY sample program and I've flash all the nessesary firmware onto the nrf9160dk baord. However, when I turn on the nrf52, it...
Hi,
I am building the CoAP client and sever example programs on a third party module (Reytac MDBT50Q). I am using Reytac dev board MDBT50Q-DB-40. Unfortunately the example...
Hi all
Can the NFC tag of nRF52832 be integrated with multiple cards？
Such as t he access control card of my dormitory and my home can be replaced by one card
Thanks...
I use the connected mode of DF, i use the two receiver,one transmiter,but when i flash the procedure to my boards.i find that only one receiver can get the IQ samples.how...
I am trying to port some code I wrote for Gazell, which I guess acts more elegant since it uses PPI, a workqueue, timeslots, etc. I have an ESB connection in which I receive...
Hi,
I am currently developing with the nRF52 DK (nRF52832 SoC) and the nRF52833 DK (nRf52833 SoC). I have built and flashed the Bluetooth: Peripheral HT sample from Zephyr...
HI,
I'm using nrf51822 and Gazell protocol.
from the RM, i get that the combined length of S0, LENGTH, S1, and PAYLOAD cannot exceed 255 bytes, which i think i can set the...
hello everyone, recently I entered the world of nordic,
and I have been testing some of the functionalities, of one of the devices,
specifically the nrf5304 dk model,...
Hello,
I created a device on AWS and corresponding certificates/shadows on the us-west-1 server. I'm able to successfully connect and send to this endpoint, but want to...
Hi Sir / Madam,
May i know if there is any layout guidelines that available for nRF5340-QKAA?
Appreciate if you could help to provide to ease the development of the...
My app uses mesh shell to subscribe to messages on a custom model and that works just fine
I need to subscribe to a different address on the same model but get an error...
