Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi guys,
I try to integrate the flash logger backend .
When I run the code I get the following error:
<error> nrf_fstorage: addr_is_within_bounds(p_fs, dest, len) check...
Greetings. I am developing a application that will run on a custom board based on the nrf52833 MCU. During development we have been using a nrf52833 development kit for testing...
Mr. Jared i do apologize for having accidentally verified&closed the issue but to answer your question we've found that the module we were using did not possess a 32khz crystal...
Hi,
I am using the code provided at https://devzone.nordicsemi.com/f/nordic-q-a/85850/example-for-extended-advertisement-receive-node
to send more than 60 bytes, but unable...
hi,
I have a problem about NCS1.9.1 NVS.
I performed `nvs_write` when ble is connected and then a reset occurs:
Whether NVS write can be performed when bluetooth is...
Hello All,
I'm new to using Nordic development kit and VSCode but I am running into an issue when I am trying to build a sample application. When I use the template to create...
I am using bt_nus_send to send data via BLE every 1ms. I've noticed that when connection is bad, this function takes a couple of milliseconds to execute, while when connection...
Hello,
I'm currently developing on the NRF9160, a sensor implementation that sends a few 100 bytes every 24hrs.
However, for demo purposes we need to send the payload...
Hi,
I am working NRF DK (NRF52840), when I am trying to flash the program in NRFGOSTUDIO from that it was showing some error that is " No device detected, or readback protection...
Hi, All
I am using VS Code and nRF connect v1.9.1, I try to set some parameters for scan etc. during running. It would be ideal if they can be saved into NVM and loaded...
Hi,
I am conducting a mesh test and it contains:
An android smartphone,
- running nrf mesh 3.1.7 on github
- sending hundreds of bytes packets to the mesh nodes...
Hi,
I am completely new with the development kit nRF5340, I have plugged in the USB and turn it ON, the status after that as follows,
- LED5 is blinking continuesly
...
Hi I have been doing some current consumption measurements using Nordic's Power Profile Kit 2.
The device I am measuring is a custom BLE device that uses the ADC to sample...
Hello, I'm having problems to debug my application when I check the "Enable debug options" in the build configuration. If I don't check this box, I can debug, however, most...
