Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi all, I am using SPIM with dma list triggered by gpiote. A gpio low-to-high event starts spim reading, and it works fine. However, I need to read different length at different...
Hi,
I am getting following problems while executing ble_gls example.
1.device gets disconnected immediately after connecting
2.getting timed out error problem
Kit...
Hello DevZone Developers,
Presently, I am trying to find H/W which support BT 5.1 Direction Finding.
I came across this , where it is mentioned that "Nordic Semiconductor...
Hello
I am contacting you because I have a problem with the "otThreadSendDiagnosticGet()" function. In my program, I am trying to retrieve the list of RLOC16s of the children...
Hi,
As I mentioned in the title, I am using the `pc-ble-driver-py` python package which is basically bindings to the SoftDevice running on the nRF52840 dongle.
Here...
hello Nordic
i am using nrf52840, sdk 16.0, working base on the peripheral app_ble_blinky example
i wish to use the p0_11 pin for pulse generation (not pwm), but when...
Hi,
We are running the smp_srv on the nrf5340 NET Core, we suspect the example is writing the firmware image to the NET core instead of the APP core. How do we have to modify...
Hello all! Where is located the i2c example for the nrf51822 device? I am using the nRF5_SDK_12.3.0 . And i can just find and i2s example. Best regards!
Hello. I'm currently developing a software for nRF52832AA device. It needs to communicate with external device via UART. It resieves text message and takes some data from...
Hi there,
My question refers to the nRF SDK: examples\dfu\open_bootloader\main.c
When the example is built, the output HEX file contains a section that writes the Bootloader...
How do I get putty to receive output from the Thingy91? I see output in the LTE Link Monitor with the following prj.conf config:
CONFIG_USE_SEGGER_RTT =y
CONFIG_RTT_CONSOLE...
Hi!
My apologies if this question has been asked and answered previously (searched, but didn't find).
We are still developing with ncs version 1.3.2, but would like to...
Hi,
can someone tell me the correct order of AT commands to connect to LTE, activate PSM?
My findings so far:
AT% XSYSTEMMODE=1,0,1,0 => set LTE-M and GPS mode...
Hello, i'm using NCS 1.4.99 with a nRF5340 and i'm trying to use BLE and radio synchronization in the network core. My code run can run minutes without problem but sometime...
Hi,
I am trying to implement the AWS Discovery Sequence with the nRF9160DK board as the AWS Greengrass connected device. I am using the nRF Connect SDK v1.4.0 and used the...
