I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello,
I am trying to connect to my nRF52832 through J-Link v6.22g. This version doesn't contain the RTT Viewer GUI, but instead I am trying to connect through the RTTLogger...
Hello,
I'm using the nRF52840 in a new design, following the reference designs as a guide. I've noticed that the reference layout files and the development kit use a different...
I've been trying to integrate the Mesh SDK 3.1.0 alongside the nRF5 SDK 15.2.0 on a custom board. I've integrated the light switch server example as part of the code (replacing...
So i was merging a code from peripheral to dual mode which caused my softdevice to change from s112 to s132 .I used the proper flash placement xml file also.After merging...
Hi Sir,
I am use S132 softdevice and it converted to binary file using srecord tool, the add binary file into IAR project seems not working for softdevice.
Below is my...
Hi! I'm brand new to Nordic development. I am unable to get blinky working for the nrf52810 SoC, running off of the Rigado BMD-330 evaluation board; however, I am able to...
I'm having what I believe is a hardware problem on a custom board with an NRF52832. Unfortunately I cannot share the schematic, but will try to describe the symptoms and will...
Hello,
I also think my question seems wired, but I have a situation to make same production of 2 type about BT exist.
I will use 3rd party BT module when BT type product...
Hi all,
I have a problem where I get a Flash page erase failure when scanning interval/window is 3.125 ms (or other very small value).
(SD132 2.0.0, SDK 11.0.0)
When...
Hello,
I am currently working on a custom nRF52840 board. I have to make the nRF52 communicate with a chip using TWI, so I started from SDK 15.2.0 TWI Scanner example...
Hi!
I try to compile secure DFU from examples SDK15.3 for nrf52810 (pca10040e_ble). I added old files from DFU SDK15.0 in to my new project. Also added file micro_ecc_lib_nrf52...
Hello ,
I saw some examples in nordic forum in that they measured coin cell battery voltage level
how to interface 22v battery to nrf52832?
Thanks
learn
hello everyone,
In my application single central(ble_app_uart_c) scanning and check each peripheral(ble_app_uart) Mac id. which peripheral mac id is defined by central,...
Hi all,
Can anyone suggest me how can I flash raytech dongle nrf52840 ? I tried two following solution
1) I tried using SWI interface with dk board ,getting an error message...
