I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
hi
i create mesh network using the light switch client/server every things work well!
i have number of client and only one server.
i set the server to subscribe to the...
Hi,
i'm trying to sort out a performance problem I have with Android clients connecting to my nrf52832 using ble_nus service. Notice my problem is not about the absolute...
I am successfully using the ZigBee OTA upgrade example, but the firmware upgrade takes quite long, approximately a half an hour, so it is not an adequate time at the firmware...
Hi,
I'm using nRF52840 with SDK15.0.0 wit code from : https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial
I could make...
Hi there! I'm an engineering student who is just getting started with all the ARM SoC's and BLE environmenment, in order to develop a project for college. The project that...
I try to test Relay performance of BLE mesh, my setup as following:
1 one client loaded light switch client;
2 two server loaded light server with Relay On;
3 one sever...
Hi, I'm looking to use the nRF9160 DK as an IoT Bluetooth Gateway as listed on the nRF9160's product page. Basically, I am tasked with connecting two nRF52840's (both in GATT...
Hi, I am developping a product with battery power. To preserve the battery life, this product needs to work in low power mode. How can configure nRF51 to advert in low power...
Hi,
I'm using the PCA10056 as a JLINK to my custom board. My board is powered by a LiPo battery through VDDH, and I have access to the SWD pins. I'm also using Segger Embedded...
I started from the blinky example for pca10040e (NRF52810) on SDK15.3, added some files and code to get TWI_MNGR working but i get an error which i can't solve
`.nrf_queue...
Hello
I am currently trying to read data and save the timings of it. When pushing a button on my custom made PCB, the microcontroller goes to the handledata function....
Hey,
So I've been using the Verizon SIM card supplied by nordic with our nRF9160 dev kit. I never really new how the APN was getting configured because it just happened...
Hi, I have DK-52840 where the ATMEL ATSAM3U2C is the on-board debugger. I replace firmware via my J-LINK ULTRA+ JTAG through 10-pin connector on-board, I used J-Link Commander...
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.2.0/hardware_driver_pwm.html
Where are more docs like this explaining how to use the drivers?
