I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello, I am currently working with VEML6035 light sensor and so far i had a hard time working with its 16-bit registers.
The code that i wrote:
overlay file:
I can...
Hi,
It seems like my system is crushing before going to deep sleep,
I have noticed that if I remove a k_sleep of 500 ms, just before going to deep sleep the system does...
It's successful when I use west :
% west flash -d build
But it's failed when I use nrfjprog :
% nrfjprog --program merged.hex --reset
OR
% nrfjprog -f unknown...
Hi nordic:
I use two NRF52DKs and download MESH CHAT separately, hoping to achieve communication between the two NRF52DKs:
SOFT VER: NCS2.8
The specific process is as...
Now I have a verification work on the nrf52840 development board, which is to verify whether the terminal device will perform signature verification after receiving OTA firmware...
I just freshly (Nov 25, 2024) installed the nrfutil 'core' exe and the nrfutil device command.
I try to list my nrf devices (a nrf52840 dongle is connected and another nrf52840...
I have some of these boards which come already flashed with the AdaFruit CDC/DFU/UF2 bootloader , allowing them to be programmed without a dedicated programmer. I wanted to...
I have noticed that the project name used for sysbuild is the same as the folder name where my code is checked out. So if I have the application in a folder named "src" the...
Hi,
I had a problem while programming my custom nRF52832 board using nRF52840DK. I am using this connection that I found in the Nordic Devzone forum. I am trying to program...
I'm developing my project by nrf5 SDK in nrf52832.
Pairing and bonding used in my project and implemented by peer_manager.The pm_evt_handler() defined as follow:
Due...
Hello everyone,
I was looking at SPAKE2+ example (NCS v2.6.99) and trying to understand where the password used to derived the shared secret is set or used. Can anyone help...
Hello,
I'm trying to move my project based on the xiao_ble board from using SDK 2.6.2 with Adafruit_bootloader to SDK 2.9.0 with MCUBoot/sysbuild.
To keep things simple...
nRF5_SDK_17.1.0
PCA10059
For I want to provide up to 20 central connections, I have defined the objects like this( inherited from example code):
The conn_handle is...
I have built my own firmware for my nrf54l15 custom board and got a merged.hex file.
Now I want to flash this firmware(merged.hex) to my nrf54l15 custom board on another...
Hi,
I have updated and old old project to SDK 17.0.1 and using Segger Embedded Studio
But because I make a lot of use of pstorage in the project - I am not ready to convert...
