Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hello Nordic
trying to migrate from ncs 2.5.0 to 2.7.0
well i did the mistake of installing the toolchain via the vs code .. for some reason it installed it in the wrong...
DFU is now implemented on ipads and iphones, as well as on Android phones, and the app platform is nRF Connect. The problem is that the firmware upgrade can be achieved normally...
I was trying to build off of the example of Lesson 6, exercise 3 from the Intermediate course on DevAcademy.
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate...
Hi there,
I am trying to interface SPH0465 microphone with nRF Dev Kit 52832 with the following configurations of I2S:
I have followed the code from echo example...
Hello!
I am hitting a really frustrating issue running Zephyr on a XIAO BLE Sense module which is based on the nRF52840 MCU. I am simply trying to verify development setup...
Hello,
On a pairing failure from iOS (either cancel or timeout of the pairing dialog alert "Bluetooth Pairing Request"), the device no longer allows pairing until a software...
Recently our firmware team encountered a new version of NRF52840 and our hardware team "orders the available chip". How can I know and manage the version when we design the...
I was wondering whether having GATT client and server in same chip (NRF52832) would work? If so, then how would I need to set up bt_conn_auth_cb on zephyr if both uses passkey...
Hi,my board is nRF52840dK,and the SDK is ncs 2.7.0.
I want to modify the subevent parameters,
Is there any API to modify them in my code but not in prj.conf? such as ...
The provisioner sample was used as the base code for adding the function to set model's publication address. After doing so the end node goes into
Requesting Help regarding...
I currently am using a nRF9160DK. I want to have the nrf52840 on it scan for BLE devices and return the device count and then send this over UART to the nrf9160.
How can...
Hello,
I am contacting you today because I recently bought an nRF5340 development kit, as well as several Nordic Thingy devices (52, 53 and 91) and I have been working on...
Hello,
I am contacting you today because I recently bought an nRF5340 development kit, as well as several Nordic Thingy devices (52, 53 and 91) and I have been working on...
Hi, I was reading through the errata for SoftReset and see a note: [161] RESET: Network core is not fully reset after Force-OFF
Can you please clarify how to reset both...
I'm trying to use Adafruit LSM6DSOX (I think it's a misprint and it's actually LSM6DSO), regardless. I can get it to work using I2C but I need it over SPI.
I have been racking...
