In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hello, Our application image became too large for TF-M and we're investigating the use of PSA Protected Storage without TF-M as described in NCS 2.6.0.
When writing a new...
Hi,
I encountered a modem fault (NCS v2.5.1, mfw 1.3.4, nrf9160DK). Here's a portion of the log leading to the fault:
[24:36:01.333,312] <inf> gnss: event NRF_MODEM_GNSS_EVT_PVT...
Hello!
I am a beginner and am trying out an MQTT example on my nRF9161 DK that I recently bought in my Visual Studio Code on Windows 11. I am aware that the sample application...
Hi,
I am able to get my CA certificate working using TLS for MQTT. but im not able to get the TLS Client certificate working.
I had created a client certificate as per...
Hello, I'm following along the nRF Asset Tracker guide and I'm on the step 'Create device credentials'
Running the command
' ./cli.sh create-and-provision-device-cert...
Hello support.
A new design is looking at using nRF24L01+ to communicate wirelessly. I'm aware that this IC is no longer recommended for new designs, however, it's the one...
Hello,
I am trying to use the LTE modem serial example on a customized board that communicates an NRF9160 SICA B1 with an external STM32 microcontroller through the UART...
I am using the nRF52840 with NCS SDK v2.5.1. I tried to implement non-volatile storage in my application, and it is working on the DK board, but the code is not working on...
Hello,
I am using the DK Buttons and LEDs module to get the status of my button on the ANNA-B402C ( nRF52833 ).
I wanted to check if any debounce filter/mechanism software...
Hello,
as mentioned in the subject, I want to use single bank while CONFIG_BOOTLOADER_MCUBOOT=y. The reason is that the nRF7002 firmware is so large, it would cause an overflow...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I want to debug using the Logger module...
Hello,
I am developing a nrf5340 project based on the Nordic AWS IoT library. Connection is via Ethernet (W5500) and it works fine as DHCP and SNTP works fine and I can...
Hi,
I'm using nRF5340 Audio DK with a modified example code provided by (thanks again!), which integrates peripheral NUS through extended advertisement in parallel to...
Hi, I am using nRF5340 dev kit. I have successfully accessed external NoR flash (mx25r64) over qspi. But once I enable BLE with setting 'CONFIG_BT=y', I got littlefs mounting...
