In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi,
I have a project for nRF52 in VS Code. The project was able to compile and everything worked fine. However, after about a month, I reopened the project and now there...
I am developing LTE-M software on nRF9160. Previously, I checked that it runs well with nRF9160DK. Now I try it with my own board.
First, only for testing, I made following...
Hi, I'm trying to set up wireless audio stream using 2 nRF52832 Dev Kits and SGTL5000 audio boards. SDK: nRF5 SDK 17.1.0 For the wireless protocol I've used ESB, and the program...
Hi, I've been trying to modify some of the nRF5 SDK 17.1.0 BLE HID examples to make the nRF appear as a BLE HID Braille Display, that would be recognized in Android's TalkBack...
Hello,
I'm modifying the code of Wireless timer synchronization among nRF5 devices blog to use RTC instead of two TIMERs. I started with the code on Git for SDK 16. Writing...
Hello,
I am trying to interface a TCA9548A Multiplexer on my custom board. I am able to set up the channels and read the channel status' with device_get_binding successfully...
I'm just trying to get my feet under me to write some code for the nina-306 module. I'm playing along, and following the dev academy course. I can't tell if this worked or...
I'm trying to do my first Blinky app with nrf52811. I followed all installation procedures by DevAccademy.
I created a new application by the available sample (blinky led...
Hello,
I am currently using the BLE NUS example from the Nordic Dev Academy course for BLE ( https://github.com/NordicDeveloperAcademy/bt-fund/blob/main/lesson4/blefund_less4_exer3_solution...
Hi all,
I am trying to use MCUBoot on the nRF52840, and am having troubles with this: Whenever my device boots, it always immediately goes to bootload mode and I can't get...
hi all,
ST7735 driver for TFT Display which is tested using example/peripherals/GFX library, we want to test touch screen for this display ,the touch screen driver used...
I am currently working on a project using the nRF52840-DK and the Power Profiler Kit II. I have created an application based on the "NFC System Off" sample. However, I am...
Hi could you provide any insight on the following issue:
Source code in main.c
#include <zephyr/kernel.h>
#include <zephyr/device.h>
#include <zephyr/drivers/sensor...
Hello,
I have developed a Zephyr BLE project with the MAX30102 sensor. I tested the code successfully with the nRF52833 DK, and it works fine. Now, I am trying to flash...
