I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi,
After lots of issues with build and deploy, I eventually have a working version of a BLE App running on a XM122 Radar module. This module have to be packeaged with the...
Hi devzone
there are 2 nrf52 dk board - one is client(ble_app_blinky_c) and the other it peripheral(ble_app_blinky)
and I made it so that if you push the button3 on...
I need to port some functionality that is using nRF5 SDK 17.0.2/ S332 SoftDevice v6.1.1 to an older firmware using nRF5 SDK v12.0.0/Softdevice 332 v2.0.0. It looks like Softdevice...
I'm trying to build the documentation on a Windows 10 system. I've installed all of the required tools and made it to step 4 when I get the following:
C:\ncs\v1.9.1\nrf...
Hello All,
I have a problem when I build my project from sample central_uart & peripheral_uart .
I have two nrf5340 called A and B . B scans the broadcast to A to establish...
I'm having problems reading channel AIN7 in the rRF52, SDK11
I configure every channel in a similar way:
//adc_channel_5
{
nrf_saadc_channel_config_t channel_config...
Hi I am working on nrf52840 dk project. I want to find out the maximum stack usage of the program.I searched in the devzone support forum and stumbled upon this method to...
Is there a problem with writing-to and notifying-from the same characteristic? Or is it recommended that one create two characteristics, one for receiving data, and the other...
Hi everyone,
I am using the nRF52840-PDK and nRF5_SDK_17.1.0_ddde560, And trying to enter System Off modes with no RAM Retention.
I use the ram_retention example from...
Hi,
I have met a problem that I try to advertise nRF52840 dongle in pc-ble-driver-py. However, connection is not built from this command:
The uuid is uart over ble which...
Hello Nordic family, I hope everyone is fine.
I want to do modifications to the nRF Toolbox android App such that the data received by the nRF Toolbox android App from the...
I'll start off by saying, as a new developer, Nordic has made an absolute mess out of the docs. The default example 'TWI_sensor' starts with easyDMA enabled, meaning it defaults...
Hello,
I am using nrf5340 module with external hardware audio codec to test stereo audio output.
I use nrf5340 module as the headset to connect with Pixel 7 mobile phone...
Hi Nordic Team,
The default stream direction is undirectional, so I add CONFIG_STREAM_BIDIRECTIONAL=y in prj.conf, then use " python buildprog.py -c both -b debug -d both...
Hello,
We have a fitness application that employs concurrent use of ANT+ and BLE communications on an nRF52840, that we wish to port to the nRF5340. The product brief...
