Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi,
In the documentation of SDK 17.1.0 it is stated that only s132 v7.2.0 is supported. I want to update from SDK 16 to 17, but don't want to update softdevice, currently...
Using the nRF9160-DK together with the Power Profiler Kit 2, I observe sometimes a longer period (1 minute) of a 50mA consumption before entering PSM mode.
Is there a explanation...
Hi,
Our application has a GUI, the UI data is stored in the QSPI flash and it is independent of the firmware,
We program the QPSI flash via the PC tool in the development...
Hi , I got my Nordic Thingy : 53 I wanted to connect other sensors to the Stemma/qwiic port of it . Can you share some documents or example of how to connect multiple sensors...
Hello, I have a problem regarding production flashing a nRF52811 device. We are using a Segger Flasher Compact, but I also tried a Segger J-Link Compact. To flash we are using...
We used 52840 chip to produce a near field communication module, the antenna is on board antenna, some problems occurred during the verification process, can your engineer...
hello Nordic
i work on nrf52832, trying to run it with zephyr application
one board runs fine (more/less, there are some MPU FAULT issue that i am facing with no luck...
Hi everyone,
I have some issue when my device is in very low temperature of -60°C / -70°C.
We use an NRF52832 (SDK 15) on modules (BMD-300 frome UBLOX formely RIGADO...
I'm working with lsm6ds33 sensor using lsm6ds3 driver I get some results, but they are ae rarely modified and didn't follow the IMU motion so how can I correct this.
(The...
Hello,
When I use sntp to get the timestamp from time3.google.com, getaddrinfo returns a -10 error. nrf9160 device also reboots automatically, why did the device reboot...
Power Profiler app v3.5.0 running in nRF Connect for Desktop v3.12.0 in Ubuntu 220.4 reports "No Supported Devices Connected".
I have used my PPK2 successfully recently...
Hello team,
I was not able to receive a suitable reply for this post for almost two weeks. I started thinking the engineer had gone for vacation. That is the reason I...
Hai, how you doing?
I am facing difficulty in trying to connect ble devices with windows 10. I am using BLE dongle APLIC WDP 304747 (Also tried another couple of BLE dongles...
In nRF Connect SDK 2.1.0 the devices in the DTS file are missing the "label".
For example, in nRF Connect SDK 2.0.0:
gpio0: gpio@842500 {
compatible = "nordic,nrf-gpio...
we are using NRF52840 , with a SD card. Data is stored in SD card in Text file or .csv file every 10 mins. We want to push the data to Mobile App either using the BLE or using...
