In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
HI
We are currently manufacturing products using the nRF52832, but some receiver sensitivity issues have been reported and are currently under review.
1) Inspection...
Hello,
I am deploying a thingy 91-x sensor outdoors to record acceleration data. I am reaching out requesting recommendations on what kind of solar panel would be able to...
Hello all,
I am trying to prove that I can compile and upload some simple code that I have written and run it successfully on an nrf52840.
I'm using an mdbt50q-db-40 development...
Dear Nordic Team, Does the nRF54L15's channel sounding function use the channel range of 79 channels (72 channels excluding the advertising channel) stated in the Bluetooth...
I just got my DK today and initially wrote the blink command to make the LED blink, which worked fine. Later, I wrote the AT command back, and the LED just keeps blinking...
I am developing a BLE mouse that can connect to 3 devices using nRF52840.
The sample code (peripheral_hids_mouse) allows simultaneous connection to multiple centrals....
Hello Team, We are currently building a circuit using nRF52840 CKAA (WLCSP -94) .We have configured P1.03 & P1.05 GPIO pins as UART_TX & RX . Kindly confirm if this pin or...
Hello, I am currently developing on the nRF54H20DK, which i have previously used v3.2.0-preview1 for. Everything works fine on v3.2.0-preview1. I have tried bumping to v3...
I am using the zephyr\samples\subsys\nvs example. By default the program stores data in internal flash in storage_partition. I would like to create a custom board file for...
I am using the peripheral_uart example. Now, our device tree seems to have crashed. Before the crash, I added the following configurations to prj.conf of the application core...
Hello,
I'm having some issues with the channel sounding on the nRF54L15. I'm using two nRF54L15-dk and two custom bords with the nRF54L15.I'm using SDK v3.0.2 for my software...
I’m trying to debug an existing product by opening its old firmware project on a new PC. The project uses nRF5 SDK for Mesh v2.1.1 , SoftDevice S132 , and nRF52832 .
I installed...
I am currently working in project with nrf54l15dk and 3.0.2 sdk. I'm trying to work with peripherals and I want my project to do the following: -Have 2 PWM outputs that used...
Hi DevZone Community
I'm trying to get a simple Hello World sample to run on an nRF5340DK board with a 2.8" ILI9341 based TFT display that has Arduino headers attached ...
