I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
Dear Support Team,
I'm trying to test 802.15.4 feature with the precompiled radio_test hex file, but got an error when connecting the CLI through PuTTY. Below is the detail...
I am very new to the Nordic line and I have an nRF5340-DK that I would like to build a basic BLE Remote Control project. The Remote Control must pair with a phone or computer...
Hi,
I am using VS code for my project, which is using bl653 board. While in build configuration setup in vs code am getting this error. ERROR: source directory - does not...
Trying to add UART capability (sample project from console) to a a ESB transmit sample project. Could not get a build assert to work.
1) Tried to add all of the selections...
Hello,
On a BLE Central, how can I enable connect with auto connect to a peripheral with previously saved bonding information.
Once paired and bonded, I can recall bonding...
Hi everyone,
I am updating firmware for mesh using following this commands:
PS D:\nrf5_SDK_for_Mesh_v5.0.0_src> nrfjprog --program .\bin\softdevice\s140_nrf52_7.2.0_softdevice...
Hi everyone. I am writing to have an important info, that is, is it possible to load a .hex file, preloaded in an external flash, to program from my application in the nRF52840...
Hi,
As shown in the subject, I am developing a product which needs to support extern Flash-based BT OTA-upgrade. So w here can I find examples of OTA-upgrade using external...
Hi Nordic
In our product, nRF52832 is connected with another MCU through UART. We find that the overshoot in UART signal is very high.
The yellow one is the TX signal...
Dear All
I am trying connect/disconnect function with the DK, it gives me some reason codes, my app is based on central_multilink, which I cannot find their meanings, could...
Hi nordic in our product nrf52832,guided by the tutorial developer.nordicsemi.com/.../README.html,we find something strange. as we have 3 nrf52832 chips in our product,two...
Greetings,
One query on the very useful eDRx notifications in NB-IoT mode (nRF9160 SDK running 1.3.1 FW, used with MoSh app) :
I have just noticed that sometimes when...
With reference to the following known issue: NCSIDB-114: Default logging causes for nrf connect sdk 1.3.2. Is there any further documentation regarding the workaround mentioned...
Hi,
I have installed Segger Studio for ARM v6.22a.
I have also installed the SDK5 version 12.3.0.
I imported the IAR project project ble_app_start_notification_pca10028_s130...
Hi,
The datasheet of nRF52810 says that, if the voltage drops below the operating voltage, the device shall undergo a brownout reset itself and it is supposed to work normally...
