Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hi.
I would like to make an app for communicare with a can device. I see that the chip mcp2515 is a popular one .So i purchsed some dev boards with this chip. One of them...
Hello,
I have a question concerning the decryption of a 90 byte AES CTR ciphertext with a given 16 byte key and 12 byte IV (=8 byte nonce, 4 byte counter).
I've tried...
Hi,
I used the nRF Programmer included in nRF Connect to flash the custom PCB. After the update to 2.0.0 J-link is no longer detected under devices. Could you help with...
I was flashing nRF51822 used ST-link, with file hex from SDK example, so now i want flashing a different .hex. How can i do that? I try do like before but I CAN'T
I'm trying to dynamically allocate some data, send it over NUS, and then free it, but I'm not sure when the SoftDevice is done with it and it's safe to free. Would the following...
Launched nRF Connect for Desktop this morning (v3.7.0) and was prompted that an update was available. Performed the update as well as child packages. PPK was updated as a...
Hi, i have a problem with nrf mesh. nRF5_SDK_17.0.2_d674dde
nrf5_SDK_for_Mesh_v5.0.0_src
nRF52-DK(PCA10400)
Android 6 and 10.
Bluetooth 4,1 4,2 5.0.
I use example...
When using USB with CONFIG_NO_OPTIMIZATIONS=y I'm getting a usage fault and Zephyr gives the reason K_ERR_STACK_CHK_FAIL. The fault looks like it occurs in the unnamed thread...
Hi,
In case the FMFU fails or the device gets into some recovery state. Is there a way to get IMEI without enabling the modem library? When the modem is in process of failed...
Hi,
Can you please tell us how to send Hex data using AT#XSENDTO command ?
I am using the "Serial LTE" application. In the old SDK version (v1.6), it was possible to set...
Hello,
I recently saw this post: https://devzone.nordicsemi.com/f/nordic-q-a/71940/low-power-mode-using-saadc-with-ble_app_beacon and I'm interested in the example for measuring...
Hello Kenneth,
I am trying to program the nRF52840 Dongle with the HEX file according to "Programming the nRF52840 Dongle". The dongle is connected to USB port and the LD2...
Hello,
I try to port project from IAR to Segger Studio. I followed the guides for porting projects like this and this . So, I did:
- Imported IAR project to SES with internal...
I am using nrf52833dk and download nRF5_SDK_17.0.2_d674dde when i build the code the code the following error occur
asBuild target 'nrf52840_xxaa' compiling SEGGER_RTT_Syscalls_KEIL...
I have an "old" nRF5340-DK which I use to program an external board I am developing. I have no problem with the J-Link/SWD connection to my external hardware using the J19...
