Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Im install nRF Connect SDK 1.5.1 trough nRF Connect 3.6.1 Desktop app to learn zephyr RTOS and switch from nrf5 SDK to it but there is some bug and "Configure nRF Connect...
Hello,
I just receive a PPK2 and looking at power usage/profile. Below is the captured profile when the application is run from the debugger and then detached. This captures...
Hello,
ncs1.5.0
As shown in the question,
I use rtc to generate a 1kHz square wave, and use an oscilloscope to measure only 964 Hz.
Is there a problem with where I...
Hi.
I am using the oberon crypto backend module to use LESC in the application firmware. (I referred to the GLS example)
And I am trying to add a boot loader to use DFU...
Hello all, we are trying to set up a project with a nRF52840 chip in combination with 2 Acconeer A111 sensors. So far I have worked with a nRF52840 development kit and the...
Hello Team,
Could you please share some sample application or procedure to handle power modes (Sleep, Deep Sleep, etc) of the nrf9160.
Please let me know.
Regards, ...
Hello Nordic,
I am using Nordic 52840 (SPI Master) with Intan RHD2216 (SPI Slave) to get data through SPI from the Intan chip.
I have used the Nordic software development...
Dear friends:
I flashed a mesh serial example. I scand mesh beacon by the function "scan_start()". As you can see in below code, I got two uuid device, I want to select...
Dear friends:
I flashed the serial mesh example from Mesh SDK and contact the DK with pyACI according to the guide Using serial interface for provisioning and configuration...
Hi,
I'm looking at using the NRF9160 in a system where every microamp counts. The NRF9160 already includes a DC/DC converter, but as I understand it is step down only...
Working on an application that can be compiled with BLE functionality turned on or off, I found my "BLE off" configuration failed to compile with the following error while...
Hello -
I am trying to print a 64-bit unsigned integer (uint64_t) to a CLI output. I've based this on the CLI examples in SDK 17.0.2. Specifically this is the function I...
refer to: http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_multi_image.html developer.nordicsemi.com/.../partition_manager.html
Where I change those image...
My accelerometer readings appear in my segger embedded studio "Debug Terminal" window.
It looks like this.
I want to stream the data via COM port to this "serial oscilloscope...
