Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
hi ，
thank for your browse，when i develop my keyborad,there is a problem in the use of usb.
this is my board hw:
and use pca10056 kd,and program the hex of road...
Hello, everyone!
I have arduino nano 33 ble board. I understand that this board contains nrf52840 and can be used in nrf sdk. I will connect the debugger pin and J-link...
Hello!
I am using an saadc examole to get sensor value using AIN3 and sending it on ble but now i want to make it interrupt base example can someone help me out how to do...
I am researching a way to send audio from a Microphone on an APP in iOS or Android and came across the Thingy:52. Is it possible to get some guidance on the App side to transmit...
I would like to use an analog microphone to generate a voice signal, measure it by an ADC, and then transmit the sound to the host. This is the cheapest solution, but I'm...
Hello,
I'm trying DFU from here . It works successfully with nRF52833 DK Board before Appendix 1.
The question is how to combine all which it is bootloader + sd +...
Hello all, I have question about ppi.
Like code shown above, I'm using ppi.
Here, MUX_INPUT_2 and MUX_INPUT_3 are name of pin.
I'm changing their state: from low to...
Hi,
We would like to know the default state of the NRF52840’s GPIO pins - is it high, low or open? The reason for this question – we need to know these pins’ behavior/state...
Hello Guys, I want to build some project with Nordic products but ı don't have any sample code , if you have sample code for Keil let me improve myself.Actually codes can...
Hi,
As has been explained numerous times in posts on this forum and many others, mapping RSSI to a distance measurement is notoriously difficult and inaccurate. I was...
Hi
Can anyone verify that it is possible to use the nRF5340 PDK to program custom nRF53 board?
The documentation says: The nRF5340 PDK supports programming and debugging...
Hello,
we are using NRF9160 +Nrf52832 in a project. NRf52832 has to be used as HCI interface..after searching for this, i came to know that zephyr based HCI uart sample...
Hi,
I am working on Eddystone project, after I successfully tested the Buttonless DFU example, I added DFU service to Eddystone example ( nRF5_SDK_17.0.0_9d13099\examples...
I am using this MBN52832DK and find out this nRF5_SDK_17.0.0_9d13099.
Trying to import into Segger Embedded Studio but rebuild come out error.
using the nrf52832_xxaa...
Hi all,
I would like to have a semi-duplex communication link over one pin (+GND). The nRF will act as a pure slave device which responds to, and acknowledges, commands...
