I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
I am beginner in nrf programming. I want to use NRF-ESB protocol to communicate between my Rx & Tx device with maximum battery saving techniques. For this i am using nRF5_SDK_12...
I enabled BLE buttonless unbonded secure dfu on custom nRF52382 based chip with s132 (SD version 6.0.0).
When buttonless service dfu control point characteristic is written...
I have established a connection with max30205, but I get only the first byte of temperature, how to read the second one? to get the tenths of a degree.
Now it works like...
Hi, I need to use a ble_hrs_t variable between two different files, I used the BLE_HRS_DEF() macro to instantiate the variable in a header file that I've included in both...
I am using the example from ble_app_att_mtu_throughput_pca10056_s140, changing the values for:
#define SEC_PARAM_BOND 1 /**< Perform bonding. */ #define SEC_PARAM_MITM...
Hi, I am following the Thread Border Router example provided in the info center. I have one Raspberry Pi 3 v1.2 connected to the internet via WiFi, one nrf52840-DK programmed...
Hello,
I am new to BLE and I'm following the solutions to the BLE characteristics tutorial for SDK 13.0.
I have successfully implemented my own external temperature...
Relationship between "LE Secure Connections (LESC)" and Bluetooth version
I am experimenting with the following contents.
・ "Central": iPhone 5s (Bluetooth v4.0) ・ "Peripheral...
I have a question about the sample project "ble_app_multirole_lesc(SDK V14.2.0)".
・ "Central": iPhone 5s (iOS V11.2.2) ・ "Peripheral": nRF52832(SDK V14.2.0, S132 V5.0.0...
Hello Nordic,
I hope you can help me. I'm using an NRF52840 DK development board.
I followed the instructions on this video to enable debug trace in Segger embedded studio...
Hi, I have a nRF9160 DK, and trying it out with my mac connected to the USB. However, I seem not to really connect to it? I've installed the nRF Connect app, and also the...
Dear All
We have implemented the the workaround because of the anomaly 195 for spim3 and it works as expected, but only once! After the following init
we can use spi...
Hi I am trying to init the serial on the nRF52840 Dongle but there are some defines missing in the boards/pca10069.h
I run this on the nRF52840 DK and it works fine.
NRF_SERIAL_DRV_UART_CONFIG_DEF...
