hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi, I am using nRF52840DK SDK 2.5.0 for testing Zigbee. I have three boards of this type, for the coordinator, router and end device.
For testing I use the end device I...
I am encountering the error <err> flash_nrf: invalid address: 0x00100ff8:8 when using NVS in my custom Zigbee project. However, the NVS functionality works properly in the...
I have a question regarding DFU while transitioning from development using the nRF52832 with the nRF5 SDK to the nRF5340 with NCS. Currently, I have a DFU app developed for...
I'm trying to install my dev environment on my MacBook. I've installed most of the tools but need the Segger installation to be properly licensed. I downloaded the Nordic...
Hello, After a lot of struggle i was finally made it to the point i can build and flash to my thingy 91 the lte_ble_gateway. However, i added prints (printk) in main.c to...
Im streaming audio from a gateway to headsets using BIS, but I am unable to get multiple streams working, so that I can switch between streams on the headsets. How do I set...
Dear,
We are using the nRF52840 with a proprietary protocol.
We plan to use the nRF52840 to sniff/poll RSSI on different (5/6) channels on periodic time (typ ~100 us)...
Hello, I have a problem on getting the dynamic tx power to work properly on the BL5340 using the hci_pwr_ctrl. I tried the example, it build and flash correctly, no error...
hi!
I get the message "The build configuration is stale. Run a pristine build" even after rebuilding in all versions of nrf connect for vs code after 2023.7.129.
I have...
I'm developing a product with the nRF52840, using Zephyr (Toolchain & SDK version 2.7.0). Is there a way to set up two PWM outputs having the same frequency and duty cycle...
Hi,
I am working on implementing an I2C node in my nRF52840 based sensor. However I am getting the following kernel panic.
I removed all I2C node related code that I...
Hi,
I'm developing a new battery powered sensor device with an NRF52840 and have some thoughts about efficient power supply. The main question is: Using an external DC...
Hi,
I have opened Sample "Peripheral_hr_coded" and added build configuration.
Then I clicked on Action --> Build.
Please validate below log. Is it proper ?
Log is...
Is it possible to dynamically switch between USB CDC (Communications Device Class) mode and USB MSC (Mass Storage Class) mode on the nRF52840? If so, could you outline the...
Hi, recently I started migrating my company's firmware from nRF5 SDK to nRF Connect SDK. I have been following the devAcademy courses and so far 1. I have created my custom...
