hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
I am using nRF Connect fro Desktop Bluetooth Low Energy Standalone v4.0.4 with a Dongle USB nRF52840.
I can see my device when Legacy Advertising is enabled, but if I only...
Hi,
First of all, let me confess, I am new to VS Code - NRF SDK environment.
I have a VS Code setup with NRF extensions enabled and due to some reason, the error squiggles...
Hi , I 'm trying to send and receive on a websocket. Sending works fine and is received on the backend, but when I try to receive I just get garbage in my buffer.
I sanity...
Hi,
I'm currently trying to add MCUBoot in my project.
The project was built successfully by adding these lines to prj.conf.
CONFIG_BOOTLOADER_MCUBOOT=y
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
I'm looking into using command line builds for nRF Connect SDK again due to issues I've been running into with vscode.
The instructions on this page ( https://docs.nordicsemi...
I have tried zephyr/sample/bluetooth/periodic_sync_conn in nrfsdk v2.7 and test on nrf5340 audio dk, and doens't work. the output is:
*** Using Zephyr OS v3.6.99-100befc70c74...
Hi,
How to solve the problem of writing data to flash using the write_data_flash function in save_stack_data function
1.1. I tried to add the function save_stack_data...
Hi! Background (feel free to skip) --------------------------------------- We have 3 nRF52840 boards, connected via ble/NUS as follows:
B also advertises bluetooth HID...
Hi, we are using the nRF9160 in conjunction with the nPM1300. To power off the device, we call lte_lc_power_off() which sends the AT+CFUN=0 command to the modem and waits...
the v2.7.0-5cb85570ca43 zephyr/ndk combination doesn’t work for things using the JSON_TOK_FLOAT type (vs the number type). this is because zephyr/lib/utils/json.c:float_ascii_encode...
I am working on a project in which i have got 100 nodes we are doing it in our custom board. so i need to assign unicast address manaully for each nodes inside it. How can...
When I try to build any application with west I always get a CMake error complaining that it is unable to run the Python version included with the NCS toolchain. The error...
I'm working with a DVK that has an nrF52840 with a Sierra Wireless HL7800 modem. The modem is connected physically to UART1 while the UART0 is used for the following as shown...
Hello
I am at the early stage of evaluation of a nRF52840 USB Dongle and I have installed all software on my Win 11 PC.
Just trying to check that everything is working...
