Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
I am attempting to build a project off of the XXX template repository. So far I have gotten the workspace set up and am now attempting to run "west build" but I get the below...
Dear Support Team,
I just started evaluating a nRF52833 DK board with the nRF Connect SDK 2.3.0. At this point I would like to start playing with the SPI but unfortunately...
Hello.
I am developing device using nRF52840 and i have question about input voltage.
Circuit is converting remaining voltage of battery using nRF52840 (Pin P0.02 AIN0...
I'm using nrfSDK17 with 52832.
When I build my code ,I will get error ad follow:
As L6407E explain,It seem that I only need to scale up IRAM size no less than 0x58....
Hi,
There is one board level hardware change in our new board design that requires different GPIO behavior.
Is there a way to program board revision number in ROM (not...
Hi all! As a disclaimer; I am a beginner with the Nordic SDK, so my understanding may be wrong. Please feel free to correct any holes in my theory. I am trying to use a custom...
Hi. I'm using nRF Connect SDK 2.6.1. I'm developing my own board based on nRF52840 SoC. So, I created an overlay file from nRF52840dk device tree. I could configure and implement...
Restarting the circuit will run the program, and not restarting will not run the program.
I used SES to develop before, and the program would run automatically after downloading...
Hello everyone,
Currently we're working on improving our DALI driver on the nRF52840 chip and NCS2.6.0, because we've experienced issues with transmitting DALI bits with...
Hi,
as a beginner in nrf world I plan to design a mini devkit with 9161. I plan SW pins connector for it to program/debug via Segger j-link and additional UART-USB interface...
Hello,
I am creating a new project that uses the nRF52810 as my controller, and during the development stage, I am using the PCA10040 nRF52832 development board. (I read...
I have three nrf5340 board. Now i want to use one as bis-headset and two as bis-gateway. I want to get two audio from two bis-gateway at the same time. Can i do it? How ?...
Hello everyone,
I'm experiencing difficulties flashing my Seeeduino XIAO BLE Sense board using the nRF52840 Development Kit (DK) from Nordic Semiconductor. Despite correct...
Hello All,
I have been trying to get the Xiao BLE Sense with the nrf52840 chip in conjunction with the expansion board to access the SD card using the FatFS example from...
I don't want to use nrfjprog as the runner. I want to use jlink runner when flashing. However it doesn't work, neither do nrfutil.
nRF Connect for VSCode doesn't work when...
