I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Dear Team,
We are registering with https://imports.gov.in/MEITY/public/home for nrf7002 modules which were sent by Nordic team through DHL.
Please send us the IC code...
Hello,
I am currently working on nrf52832 and trying to change the sampling frequency to 10KHz ,ie, 100us and keeping buffer samples as 1.
Previously in the example we...
In the product specification of nPM1100, for fixed 500mA charging limit, ISET should be connected to VSYS. In the USB-configuration (Configuration 3) ISET is connected to...
Hi:
We want to test the nrf7002 WIFI performance based on the nrf7002 PDK.Do we have relevant test firmware?
We noticed that the sdk document of V2.1.2 has a description...
hi.
I have a firmware using standard GATT, now im implementing the mesh layer.
Im using SDK 17.0.2 + MESH 5.0.0. (im not using the new sdk connect because it is very difficult...
I'm moving from NRF9160DK to a custom board, where it has no UART. I plan to just use RTT for debugging messages.
However, I found if I delete the section which defines...
Hi,
I build secure_bootloader_ble_s132_pca10040_debug example (SDK17.1) on SES 6.30.
The only modification to the project is excluding SEGGER_RTT_Syscalls_SES.c.
...
It is possible to addressing nodes using MAC address of the device in Thread network?
In topology: PC <-> Border router <-> Thread mesh nodes
which IPv6 (Mesh-Local EID...
Hello
I'm new to the nrf platform and wanted to try out the I2C functionality of my nrf5340 DK. The only example I could find was the Fujitsu MB85RC256V FRAM I2C example...
Hi,
We are nearing production stage of our project, and are looking at programming on a large scale. Using the nRF9160 we need to program the latest modem firmware along...
I have a broadcaster and a central device. The broadcaster beacons data every 60sec and goes to sleep, a configuration I have considered for minimal power consumption. Now...
During tests with a "User controlled PLMN selector with Access Technology '6F60'" one device stuck in a curious state:
nRF9160 SICA B0A mfw v1.3.3 CAT-M1, PSM: PTAU 24h...
Hi Nordic community:
Can we configure nRF52840 to support a 1.3 V VIO?
I see from the datasheet, after the internal regulator, what supplies to the chip is actually...
Getting an error from mcumgr and I'm not sure where I should start debugging this.
My environment:
nRF Connect version 2.1.0 Board: nrf52840 DK and nrf52832 DK Host: MacOS...
Hello,
I'm developing with nRF5280-DK, using Zephyr-OS with mbedtls for the cryptography, and I need to have DES and 3DES enabled by default.
I tried to set in the prj...
