How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hi
When I build mesh bootloader code, there shows flash size not enough,
Could you tell me wher I can change the size, please?
c:/progra~2/gnutoo~1/62017-~1/bin/....
Hi,
I wanted to setup a network connectivity to nRF5340DK to send RPC messages to remote server(Blockchain Network).
Already I tried to setup OTBR using RPi and nRF52840...
Hi,
We are using NRF52832 as our main processor along with an IMU sensor and a vibration motor. We are wondering if using system on mode as power off state (instead of system...
Greetings,
We are using the NCS for the development of a new product with a custom board based on the nRF52840 MCU.
First, we would like to use the Serial DFU feature...
Hi Nordic community,
I'm trying to generate a 1 MHz base clock with one of the peripheral timer, and in the timer ISR does some GPIO toggling.
I followed the nRF5 SDK...
Hello dear Nordic team,
I'm quite experienced in developing under SDK V15 and V17 but absolutely novice for nRF Connect SDK so my question may seem ridiculos. Hope someone...
Hello,
I have an application and I am using a nrf52833, as soon as i flash my application I am getting a hardfault prior to the main call. As in below snap:
I do not...
Hi,
We are using a custom board with nrf52840 and just started using our own generated keys to sign images with NRF SDK v1.9.1.
We ran into issues when trying to swap...
Hi,
I'm moving a project from SPM to TF-M. I have imported a static library and the board (nRF5340DK) restarts automatically every time the following mycli/main.c function...
Hello
I have a nRF52 based device communicating with Smartphones via an encrypted characteristic (SEC_JUST_WORKS) so pairing is triggered and established.
The encrypted...
I want to interface Lis2DH sensor with nRF52832 board. So, I had build and flash the LiS2DH sample code in nRF connect SDK with the required hardware connections. I have also...
Hi,
I got a issue ,that is when i modify the mtu where sample dir is D:\nRF5_SDK_17.1.0_ddde560\examples\ble_central\ble_app_uart_c,it will return a error :
00> <error...
I am evaluating Nordic nRF52840 Development Kit and a test tracking device from Fanstel SE840F-210.
Can I use these for Asset Tracking with Apple Find My network?
I work...
Hi,
I'm using a custom board with an nrf52832. I can also emulate using an nrf52840dk. I have to compile the bootloader because there is no LF crystal on my custom board...
Hello,
I think some corrections/clarifications are needed for the nrfx 2.10.0 drivers.
In the configuration files (for example: nrfx_config_nrf9160.h) I think the definitions...
