Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hi,I'm using nrf52832. I configured P0.20 as GPIO output,P0.22 as GPIO input.These two pins are connected wiht a 10Kohm resistor.I measured the voltage level on P0.22 is about...
Hello DevZone,
I'm using nRF5 SDK for Thread and Zigbee v4.2.0 and trying to test Zigbee OTA example.
I'm following this guide https://infocenter.nordicsemi.com/index...
Hi,
I am working on thingy91, I have created/added a BMS module in the project which gives different values for different data fields.
Everything is fine as BMS is transmitting...
Hi,
I am using TWI channel0 on my nRF52833 as master to get readings from a few sensors.
I need my nRF52833 to communicate with another microcontroller over TWI/I2C so...
I have code which works on the nRF52DK and on the Fanstel BT832 module, which does not work on our custom board with the CIAA package. Our custom board does not have an external...
Hello, we have a project in nRF Connect SDK, where we'd like to use a separate .conf file for b0n subimage in a multi-image build,
Let's say it's called b0n.conf. So, before...
Hi,
I would like to ask is there a dll file and header (.h) file for the nRF Connect Desktop Bluetooth Low Energy software? I am seeking for a chance to apply it in the...
Hi Good morning
Could you please to know the reccomendable dimentions of pad for soldering, dimentions of pad, PCB Layout for soldering component.
For example the component...
I was running Ubuntu 18.04 and Actinius Programmer was able to upload an example firmware without a problem. However, I upgraded my computer to Ubuntu 20.04 and Actinius Programmer...
I have used nrf5340 audio DK with nrf\applications\nrf5340_audio\bin\ble5-ctr-rpmsg_3251.hex in net core and zephyr\samples\bluetooth\hci_uart in app core directly after receiving...
Hello,
I want to install NCS 2.1.0, but I get the following problem.
I used toolchain manager 1.2.0 to install NCS 2.1.0. Open VS Code is now available.
I opened...
Hi,
I have a question, I use a 52840 board as the Bluetooth center. The protocol is S140. The other 51822 board is a Bluetooth peripheral. The protocol is S130. The routine...
Hi! We are trying to understand how UICR registers work. In particular APPROTECT, ERASEPROTECT, and SECUREAPROTECT.
We are trying to find a clear explanation for this image...
Hi ..i'm using nRF52832 interfacing with BG95(QUECTEL) ..when i insert my sim in the module at the time uart receiver is not working..when i remove the sim at the time uart...
