How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
In the Zephyr documentation, the explanation for NVS sector erase is a little ambiguous.
Elements, represented as id-data pairs, are stored in flash using a FIFO-managed...
Over the past 2 weeks the programmer fails to recognize my9160DK board. Instead, I see it listed as "J-Link" in the device list with a serial number underneath. The programmer...
Hello! I am discovering a new approach to nRF52 development. I used to be quite happy with SDK+Segger Embedded Studio. But as I understand it, this is an outdated method....
I can't figure out how to run sample code that uses the LTE-M modem.
I see nrfxlib has a modem library. But I don't know how to make a simple sample app that uses this...
Trying to build and flash the nRF5340 Audio application to my nRF5340 audio DK eval boards for eval purposes. Apparently this requires access to the LC3 repo so I am seeking...
Can you share the source impedance measurement for the nRF52840-CKAA? Is the T-network only for impedance matching? Do i need a filter for harmonics if I'm planning to transmit...
I'm using the pc-ble-driver-py: Standard Heart Rate example to read a characteristic just fine.
My issue is i now need to write a to a characteristic.
How would I do that...
Hi
I've recently been working on the ncp host example provided by nordic. after downloading the standalone version from the site, I tried programming the 2 nRF 52840 dk...
nRF SDK 17.1.0 with SD140 7.2.0
There is no example for how to use the sd_rand library. I've seen scant few posts that mention functions like sd_rand_application_bytes_available_get...
Hi I've just started developing with the nrf52840 and Ive been following the official documentation on how to use the programmer shipped with nRF Connect.
Unfortunately...
Hi,
In a custom nrf52840 board (DC/DC=on, LFCLK=RC, CONFIG_SERIAL=n), using ncs2.1.0, I measure through PPKII ~6.7uA in system_off mode, which is reasonable.
In system_on...
I have a similar question as in the previous post (about 4 years ago) with title "nRF52 WLCSP DCC routing - - ok to run over GPIO pins?" by Laserdan, i.e., I would like to...
Hi there,
The spec for nRF52840 says in sec 6.33.1 that for UART, "The external crystal oscillator must be enabled to obtain sufficient clock accuracy for stable communication...
Hi,
How do you export your project from nRF Connect within VSC? You may have modifications you did for DTS files, prj.conf etc, that you may miss if you focus on just src...
Hello,
The documentation for the nRF5340 says that the UICR OTP registers can only be written to a non-0xFFFF value a single time: > Can only be written to a non 0xFFFF...
