Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I want to intercept some data in the RX (in section UART_RX_READY in uart_cb() as a command with arguments. And I do not want this data to be sent on the the BLE.
After...
I use nRF Connect to scan BLE devices. nRF Connect can find ANCS2 device. But nrfutil dfu ble failed with Exception: Connection Failure - Device not found! And I can't find...
When I run TX tests with the AT%XRFTEST command, I can start the TX test without any problem but then the modem stops responding to AT commands. For example, if I send
...
Hello.
We are currently using MBEDTLS to handle DIFFIE HELMAN and AES . We have disabled all unused curves and modules, as suggested in documentation. Still the size of...
Dear all, I am trying to develop an application on Nordic nrf52840_dongle utilizing Bluetooth and Nordic Led Button Service. The application running on the dongle is supposed...
I was starting to develop for our own board based on the nRF9160 where we will just be using the LTE-M and while doing so, ran into issues with enabling the LTE. To do a sanity...
Working on a BBC microbit v2 (nRF52833) with Zephyr, I can only control the "ring" pins of the microbit's edge connector. I can setup pullup or pulldown on the other pins...
Hello,
I am using the nrf52832 and would like to know the clock sources used by the external peripherals. From the searches, I found that PCLK16M is used for most of the...
I am working with STM32-F401Re with IKO1A2 shield on it as well. I implemented the machine learning core on LSM6DSOX and I get the data of that accelerometer on STM32 F401re...
Hi All!
I am using nrf5 SDK 17.0.1 and using a radio test example to extend the range of nrf52833/20. Able to compile the example for nrf52833(pca10100).
Now the issue...
Hello,
I am not using the latest SDK, but it seems this has not changed (to be checked…). In file ./components/libraries/util/app_error_weak.c I have this sort of code:...
Our application has several Nordic devices in it. We want to hang a NOR Flash off SPIM4 (QSPI is already dedicated to another Nordic device) of the nRF5340 for storage of...
I use nRF Connect to test buttonless DFU without bonds failed. But nRF52832 receives BLE_GATTS_EVT_SYS_ATTR_MISSING event.
->static void ble_evt_handler(ble_evt_t const...
Hello everyone,
I am designing a Bluetooth repeater that will be powered eather by USB or an embedded Li-Po battery. This device will run with the nRF52833 along with...
