Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi all, I'm searching for a SPI example with NCS 1.8, I'm currently using nrf52840dk_nrf52840. I've looking at the drivers (nrfx_spi) but I still don't get it at all, so I...
Hi, I have a Nordic Thingy 91. I need it to save battery and transmit sensor data to Nordic Cloud on PIR external interrupt (if I could count number of PIR pulses that would...
Hi I am testing the Thread examples
I worked on SIMPLE_COAP_EXAMPLE in nrf52840 DK there it works fine while opening UART and enter to CLI commands and its working
but...
Hi again Nordic. I'm trying to write sensor data to the external flash continuously as there is not enough RAM to hold all the data required. However, the writing operation...
Hi,
I am using BL653 dvk to write an application for SPI, In my prj.conf, I added below parameters:
Now when I am debugging SPI master code, execution enters the file...
We are performing a preliminary power analysis with this device and have questions regarding the power consumption reported in the Product Specification. For example, the...
I've been struggling with enabling HTTP support on the serial_lte_modem. I've tried using various versions, currently I'm using NCS 1.8.99. I edit the prj.cnf to include CONFIG_SLM_HTTPC...
Hi,
I use nRF52840 and SoftDevice s140 (7.2.0). I use SEGGER Embedded Studio to compile a project written in C++. But lately I've been having trouble debugging. For example...
i've been test code from nrf51-app-button-example/main.c at master · NordicPlayground/nrf51-app-button-example (github.com) but not effect when presss any button.
I am new to Zephyr and Nordic. I onserved that to use variuos APIs it is required to declare in prj.conf file. But, where is the list and document of various commands woth...
Hi
I have a Nordic nRF51 as a Peripheral.
I have it open advertising until it connects for the first time to an Android handset.
When a connection is made it stays...
When I switch to any branch other than 1.8.0-rc2, I get the following notification:
"This workspace requires version 1.8.0-rc2 of the nRF Connect SDK, but it isn't installed...
I am developing a BLE Peripheral device using the nRF52805 and have just discovered that neither of the two SoftDevice packages offered for this chip have support for extended...
After compiling an example and attempting to connect to my board, VS Code won't connect to my board. It is definitely recognized by my computer, and the Programmer application...
