In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
I would like to know the natural interrupt priority among different peripherals of nrf52840.
Specifically I am looking for default interrupt priority between RTC1 and TIMER1...
Hello, guys. I'm using the PCA10040 and the SDK 16.0's BLE UART peripheral example. I am trying to make PWM signal below.
When PWM0 stops, PWM2 works, and when PWM2 stops...
Hello everyone,
I am working on an nRF52-DK and getting familiar with Zephyr. In this process I am currently trying to extend the BLE MTU size beyond the default 23 bytes...
Hello,
My device is a USB HID peripheral connected to a PC. There is a case when the PC is turned off, but USB power is present. I want to detect this situation.
At the...
Is it possible to detect the presence of a Low Frequency Crystal and configure softdevice to use if present, otherwise use the internal RC oscillator?
A proposal would be...
Hi,
we have troubles to use 4wire NRF LPUART between nRF52840 (client) and nRF9160 Serial LTE Modem app (server).
We use v1.5.1 of nRF Connect SDK.
For nRF9160 we added...
Hello Team,
I want to know while Ble device is connected to the android device and within 5mins if device not get any data from android device then,
- Can device enter...
I am using sdk for mesh v.5 (s140.7.2.0) and nrf52840 DK and want to add uart peripheral into the client in the light switch mesh example and then trigger button 1 once a...
Hi,
I have written Hitachi AC IR transmitter using Smart remote 3 library.
Smart remote 3 library support 2 AC protocols, i.e., SIRC and NEC.
Kindly guide me how...
Hello, I essentially want to figure out a way to use the NFC buffer received by code like the writable_ndef_message example and have that same buffer, in the same code, advertise...
Hi
the new nRF9160 Modem FW 1.3 supports Non Ip Data Delivery (NIDD) on NB-IoT In nRF Connect SDK, there is a new example that can be used to test some modem functionalities...
develop tool is nrf5340dk and sample peripheral_uart in NCS1.5.0 ,when debugging , function uart_cb() alway run in case UART_RX_DISABLED and case UART_RX_BUF_RELEASED
,code...
Hello,
I am developing a product using nRF52840 and BLE communication of my product uses NUS.
SD: s140_nRF52_v7.0.1
SDK: nRF5_v16.0.0
Recently, I want to encrypt...
