Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
Due to some problems with VTG and GND detect I sometimes program an on devkit nRF52 instead of my external board and that causes lost time, because it's not straightforward...
Apologies if this is answered in some other thread but we cannot find the precise answers we are looking for and are striving for some quick clarifications. We are planning...
The ble-sniffer_win_1.2_user_guide, Figure 4. Wireshark Interface, Packet Bytes window shows a 00 byte at location 0010, which corresponds to the "preamble" of the "Air Interface...
Hi
I want to declare 2 spi instances with only cs pin different.
The reason for dividing the two is because the modes are different.
The one declared above is executed...
I have used nRF5 SDK ver.16 for BLE HID digtiger.
I want to set up some feature value to HID report . Such as Contact count maximum.
I have followed keyboard example,...
I turned off the serial i n prj.conf of the mqtt_simple routine.
<prj.conf>
<nrf9160dk_nrf9160ns.overlay>
The idle current was measured at 500UA. This means that...
Hello Engineers,
We are trying to set the correct configuration between nrf9160 and nrf52840 for using the uart_pipe library. However we are still unable to communicate...
We have a Nordic development under way and I have run into a snag.
Neither of my dk board types (9160 or 52840) are recognized by jlink , no jlink drive etc….
I have personally...
So the interrupt on the nRF2401+ seems to be working inconsistently. I get interrupts sometimes and sometimes I don't.
For a context: I'm transmitting a sensor data only...
Hi, we recently purchased a Nordic Thingy 52 module and were trying to program it. We used a J-link recorder and a cable for the connection between the J-link and the Thingy...
Hi all,
I am using the nRF51822 and attach you can find the . .
I have noted that the current consumption is too hight for my scope (about 1.7mA). My idea is to 'reduce...
I tried: - changing USB cables and ports (no any improvement)
- instructions from this link devzone.nordicsemi.com/.../nrf52-dk-does-not-show-as-a-removeable-drive-in-windows...
Hi there,
My question is similar to https://devzone.nordicsemi.com/f/nordic-q-a/39447/central-role-in-a-mesh-proxy-node , but perhaps slightly different in that my existing...
DFU Trigger Library (USB) is indicated that only for nRF52840 SoC. For other SoCs, can I use it after some modification of the library easily? What's the limits?
Hi !
I am on a firmware project for a nrf52832. I am using SES on Windows.
There seem to be a problem when combining buttonless DFU and NUS. When I do the services_init...
