I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
The example app_onoff.c shipped with SDK For Mesh 4.2.0 (unchanged from 4.1.0) have two unused variables in its state struct.
The value_updated variable looks like a left...
Hi
Is the GPIO on the nRF62840 5V tolerant?
I see the VDD supply is capable of 5.5V.
I’m running a 5V Hall effect square wave into the GPIO pin used as an interrupt...
Hi Team,
I would like to send 10 bytes of data in mesh from one device to another device. As i know that we can send data from one device to another device and the packet...
Hello,
I've asked this question around 6 months ago. Now I have to pick up where I left off and I was wondering how much the situation might have changed since.
- Last...
Hi there!
Okay, I've been trying a lot to figure this out, but without any success. I have absolutely no idea what could be the problem whatsoever. The problem is that the...
Hi,
Currently we working on a project that uses:
nRF9160
Zyphre OS
Segger Embedded Studio for Arm (Nordic Edition) V4.52
SDK v1.3
CONFIG_MQTT_LIB_TLS ...
I am currently unable to flash any new code or to erase the flash memory of my nRF52840 Preview DK boards.
I am using SES and the OB J-Link, but also tried JLinkExe and...
Hi, I am using the TIFS register of the NRF RADIO to define the interframe spacing timing. (Done with the following line)
During a 1Mbit or 2Mbit connection, the real TIFS...
Thanks in advanced. I update uart pin number to rx:10 and tx:9, then get the error as title described under DEBUG mode. To save power, I use uart but uarte, so I set UART_ENABLED...
Hi,
I'm using the SAADC to sample external voltage to fill in the battery service. I have use APP_TIMER_DEF to create a timer to do it every 30 seconds. Also I have init...
I'm developing a Peripheral with a rather intricate connection process and doing a lot of testing.
I find that if a Central connects, and then the Peripheral tries to send...
Hi,
I have to implement customized services in my project.I think it is better to have seperate files for service inititialization.For that purpose I have seperated service...
This (in SDK v17.0.2):
Experimental: BLE Interactive Command Line Interface Example
https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.2/ble_sdk_app_interactive.html...
Hi
I have a coupe of dongles working on a project. While validating the board, i notice a strange behavior: I have the dongles in factory reset (MBR at start, the Bootloader...
