In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi!
Just to make sure - if I set
advdata.include_appearance = true ;
to
advdata.include_appearance = false ;
inside
static void advertising_init (void)
I simply...
Hi
I have implemented the Nordic Uart Service on the evaluation kit and now I would like to track the data troughput from the dongle to the board with different settings...
Hello,
I'am working with a Taiyo Yuden Bluetooth Module "EYSHCNZWZ"
This Module include the LC Network for DCDC use and the 32.768kHz X'tal.
I'am using Arduino and...
Hi all, I tried to modify the OpenThread's source codes(Just modify an API) and then built them.
Run the build_gcc_libs.bat script to build all of the libraries. That...
Hi:
I use nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_buttonless_dfu.
I want to add flash operation.
The code is as follows.
mian()
{
...............
Hi,
I am developing on a nRF52832 with S132 softdevice using Segger and SDK15.2.0. I am doing some tests with the Flash memory, and my goal is to have some const variables...
We are preparing an application to enter production and seeking to harden it to protect against unexpected system lockup.
The application is a datalogger peripheral based...
Hi,
In the Light Switch Example, on-off instruction was send to either even or odd address, may I know how can I cancel this action so that I can send the on-off instruction...
Hi,
I am using nRF mesh Android app version 1.0.3 and nRF mesh IOS app version 1.0.2
I have flashed the devices with light-switch example application under nRF5 SDK for...
Hi, I have pca10059 dongle. I soldered goldpins to swdio and swdclk lines to be able to flash it using external nrf dk. So I connected external jlink programmer and was able...
Hello, I just wanted to share a problem I encountered and make some suggestions : I lost some time looking for a TWI problem while it was actually related to the pin reset...
Hello All,
I am using NRF51822 controller in my design.
I want to monitor battery voltage using ADC pin with voltage divider.
I have LIPO battery with 3.7V and 200mAH...
Hi Nordic Support, community,
After I flashed, the connectivity hex, ble_connectivity_s140_usb_hci_pca10059.hex from the SDK v15 downloaded after executing the patch on...
development software, with versions (SDKs, IDEs, SoftDevices, ...):
Computer platform, with versions (Windows/Linux/OSX, ...) Windows 10 Pro x64
hardware revisions (chip...
