Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
There have been several topics on limitations on ADC sampling rate when BLE is in connection.
However, I didn't see notes applicable to the following case:
nRF52832, sampling...
Hello all,
I have some troubles to initialize the micro SD card with my custom board.
I have used the nRF 52 DK to write a basic code and do some test. For micro card...
I am using nrf52832 DK and am unable to build my light switch example. It throws an error that some files are not included. In the screenshot, you could see the error. I have...
Hey Everyone
I have written a code for using lora rn2483 with nrf52840 using the uart protocol which is configured on 7 and 5 pin. The program was working fine untill i...
Hi,
I am using the nRF52840 DK and the wireless_uart example from nRF5_SDK_15.0.0 to try and receive data from other 802.15.4 sensors. Using the example I can receive messages...
Hello everyone!
I'm very shy to ask probably a stupid question, but...
I'm trying get abitity to change pwm signal via ble.
I've created service, characteristic, then I...
Hello,
I am trying to get a low consumption and I detect that the activation of the ADC increases the consumption. So I am trying to configure the ADC and when I make...
NRF52832 / S332 / SDK 14.2
Step 1: connect to mobile phone as Peripheral Role, and the connect handler of service was #0 that equal to Peripheral-connection handler number...
Hello,
We are using nRF5 SDK14.2.0 and soft device s132, and trying to perform DFU of the Bootloader itself.
The process fail in nrf_dfu_postvalidate() due to wrong HASH...
i am trying to Connect a custom board with the nrf52 over the bluetooth. nrf52 is running with the BLE_nus
.i am trying to connect it with the uuid in the program is like...
Hi. I`m trying to connect two Nortdic Thingy device and receive data in same time(ex. temperature, humidity etc..).
In my application, I can connect two devices in same...
I have most of the SDK up and running with my firmware, but I cannot find where to limit the number of bonded devices to my module.
I could live with just deleting all the...
Hello,
Is there a way to get the output log for the Mesh Light Switch Demo to output over UART instead of RTT? We are using a Fanstel BT832X module containing an nRF52832...
Hello,
I am currently trying to implement SAADC sampling from three channels into the same sample buffer (device is a 3-axis accelerometer, ADXL335). The root objective...
Hi,
I am working on a project in which we have a sensor connected to the NRF52832.
I am having problem to detect the interrupts sent by the sensor.
The interrupts...
