Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
1. Are there any examples or recommendations how to realize ota dfu of ble central (device).
2. Can nrf52840 works like ble peripheral(UART service server) for smartphone...
Hi,
I would like to know how to program the code to connect the PC based on the ble_app_template.
The SDK version I used is V11 and the board I used is PCA2006, and I...
nrfjprog -f NRF52 --memrd 0x100000a4 --n 8
0x100000A4: ACAFE032 7AC54CAF
this is read by nrfjprog scipt as above and as below it is read by sd_ble_gap_addr_get.
0xCCAFACAFE032...
When creating a Server using nRF Connect version 2.6.0.
Cannot set the Descriptor 2901. It gives this error-> " Error occurred adding characteristic. (NRF_ERROR_INVALID_PARAM...
Details: SDK v15.2.0 using ble_app_pwr_profiling example. Windows 8.1. Tested uploading to nRF52 DK and Blunor BT832F.
Steps:
upload ble_app_pwr_profiling using SEGGER...
Hi,
I am using NRF 52840 DK ,rev.1.0.0(2018.36).For development using ubuntu 14 machine and segger IDE. Trying to use fatfs example with Transcend 4GB AND 8gb micro sd HC...
HI, I am seungwoo
I am developing data transmission using nrf52810.
A 300-kilobyte file is divided into 220 bytes and transmitted continuously.
11-27 17:24:24.416...
I am using the development board based on NRF 52840 from Rigado BMD340. I connected the Eval Board via USB and in the NRFgo Studio it shows that the board is detected below...
No using bootloader.
the code cant run immediately is below when i enable the wtd.
After flashing the code by jlink,the code cant run till the wtd is timeout. i check...
We are using development kit for nRF52832 and trying to create the minimum current consumption that was stated in the datasheet which is 0.7uA while the system is off. However...
I did a search on Real-time debug, it's said for nRF52810, in Code generation, should set Debugging Level to Level 3, and Optimization Level to None Is that true for nRF52832...
Hi,
I've installed arm-gcc and the dev kit, I've tried several different versions.
I got it to compile the examples just fine. I can compile the example in examples...
Hi,
I tried to run the pca10056 ble_app_uart on a nrf52840 dongle (pca10059) after modifying the example as suggested here on the devzone. I had to define the rx,tx,ctx...
