In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi,
I'm trying to utilize PPI system to generate repetitive sequence of tasks (lets call them Task A, B, C, D, E, F) at 0,10,20,40,60,80 ms every second. i.e. I need to...
Hi,
I'm trying to test adding my own custom service, but have errors when I tried to add a 128bit UUID, the test code is simple, in the service_init() function, I just added...
I am using nrf52832 and sdk 14.2.0.The software I am using is keil 5.17.the error is as follows:.\_build\nrf52832_xxaa.axf: Error: L6915E: Library reports error: __use_no_semihosting...
Hi,
In nRF SDK15, Bluetooth peripheral examples for HID devices were limited to keyboard and mouse. By any means, can we configure Nordic device as a game controller?
Hello,
I am currently learning the PWM peripheral of the nRF52DK and am a total beginner in PWM.
I have tried running the attached program and this allows the LED0 to...
Hello,
I am working on a project which requires radio transmitter and receiver to work in sync with the SPI. So the setup is as follows the Transmitter transmits a signal...
Hi,
I am trying to write my own dfu updater for the NRF51 chip and I am stuck trying to make sense of the actual DFU sequence described here infocenter.nordicsemi.com/index...
I am trying to set up mqtt between 2 nrf52s and rpi3 with the examples of sdk 15.0.2. I am very new to nrf52, rpi3 and networking. I have read everything needed as much as...
Let's send a string over UART. RTS signal will go low (active). So far, so good.
The problem is that RTS remains active even after sending is done. And because it is still...
I have two boards. I ran the exact same commands on both boards. The commands flash the same bootloader+app+softdevice+app settings hex file. One board reboots into the application...
Hello,
Setup: Running Ubuntu 18.04 inside Windows Host (using VMWare).
Device: nrf52840DK
Operating System (used for development): RIOT
I would like to communicate...
Hi,
I am running IoT LWM2m example. Everything were going fine since yesterday. when I do hcitool lescan, i see following output:
hcitool lescan LE Scan ... 28:45:8B...
I am using the ble_blinky example (s132) and want to increase the number of characteristics. I get the error code 4. I think the storage capacity is not the reason why I can...
Hi Team Nordic,
I started developing a project using SDK 15 using DK nrf52840 .
I went through several threads and started by creating a test folder inside example directory...
Hello,
I have the proximity example updating the battery service value fine using the provided nrf_drv_saadc.h driver. When converting the saadc driver to NRFX (nrfx_saadc...
