Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
I've merged the experimental_ble_queued writes sample code into my project and am testing the long write characteristic with nrfConnect from an Android phone. I get no errors...
Hi,
I am trying to figure out the reboot reason on an NRF52 in order to solve it in the best way.
We have a design with a dual supply 3.6V/5V going through a 3V LDO...
Hello,
i have a BLE Peripheral that has a service that we use to simulate UART over BLE. Very similar to the nRF UART. I consider the time to establish a link that allows...
Hi all,
I am trying to save an UART variable I am receiving. My case is very similar to the example Flash Write Example, but I would write few bytes instead of the whole...
Hello!
I have to sample audio signal from a microphone (MAX 9814 adafruit) with the nrf52 board. I use the saadc and then I perform a FFT of the data using the sdk 13 examples...
I implemented my profile based on GLS example. my profile has five services and every services have several characteristics. Pairing with several smartphone work properly...
hi,
I would like to use pwm to output the 1HZ waveform to drive the motor, but when I set the frequency to be 1HZ, I can not find the device and cause 51822 to reset.
This...
Hello, I'm working with the NRF6310 Motherboard and play with it a little with SDK 6.1, but i want to create profiles with the Bluetooth Developer Studio, so I started using...
I download "nRF5_AirFuel_SDK_2.2.0_7b89a57" and use "ptu_app_beacon" development, I am currently using "nrf51822-QFAA" and "nrf51822-QFAC", how do I set up IROM and IRAM?
Hello iam using softdevice 110 and SDK 10.0.0, Iam trying set tx power of nrf51822 using function sd_ble_tx_power_set(), i have tried 0dBm and 4dBm both are giving same RSSI...
wqewqeqwe.PNG I want to program the nrf52 chip using J link Edu -SWD mode. I actually connected the SWDCLK, SDI, and Vtref and GND of Jlink EDU programer to SWDCLK,SDI,3.3V&...
I have written a simple implementation for using the ccm module with mesh. It encrypts and decrypts as it should but when enabled the processor makes a soft reset. It happens...
I have not gone into much details of 51822. while interfacing BLE to any MCU, Is it possible to add interrupt lines from BLE module to MCU to receive interrupts in MCU. Like...
