Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
The nRF51822-EK, when powered over USB, seems to be working on 3.0V. The C232HM SPI cable is a 3.3V cable. The nRF51 data sheet specifies VIO as VDD+0.3 as absolute maximum...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hi - I saw this post and I'm not sure how to add a clarifying question on to it:
devzone.nordicsemi.com/.../
We have a similar problem in that we built our boards with...
Hello,
I am working on an application that involves sampling audio data ~8KHz. I have a few questions
The real time clock module has a maximum interrupt frequency...
Hi everyone,
I bought two NRF24L01+ off ebay a couple of week ago and started to work on them this week. I seem to have problem with establishing a reliable communication...
Hi,
I use : An nRF51822 mbed kit + Kiel 5
So I updated the firmware like this : mbed.org/.../ and I dropped s110_nRF51822_v6.000 into MBED(H:)
I successfully use...
Hi,
i read about a new Chip revision of nrf51822. So i have to buy new Development Kit. How can i find out what it is the actual DK and where to buy it. I don't want to...
Hello All,
I was looking at the flash writewrite_example and the starting address is defines as:
addr = (uint32_t *)(pg_size * pg_num);
Later in the code, the example...
Is there any updated install procedure for the nRF51822 tools?
I'm trying to follow procedure in: nRF51822 Development Kit User Guide v1.4
I have the nRFgo Starter Kit...
Hi all,
In my keyboard application, I found sometimes it return the INVALID_STATE error code , when called keys_send() , once this error code appeared, no others return...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
I've looked over all the previous posts but none of them seem to work but the most useful one I can find is this one:
devzone.nordicsemi.com/.../
The code compiles fine...
Hi,
I'm trying to build the ble_app_beacon project for the nRF51822 (pca10001 board). Using default installation folders, latest SDK (v6.0.0) and Keil V5.1.0.0. I used...