Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hi,
How to put nrf51822 in power off mode? i simply tried NRF_POWER->SYSTEMOFF = 1; in keil but it is not going to off mode. Is there any procedure before making SYSTEMOFF...
Hello, I am using the HTS example for the nrf51822.
In the example, bond information can be deleted during initialisation by holding down one of the buttons.
In my program...
Hi sir
In Desktop 2, before BTLE pairing, nRF51 uses Connectable Indirected advertising. After BTLE pairing with BTLE host, nRF51 will select Directed advertsing for saving...
Hi to all, my first experiments with NRF51822... i compile the example projects, and everything works fine (compiling and download are ok), but looking at the code editor...
Hello,
I am using an nRF51822 Development Kit. I am trying to run pca10001/board/uart_example (with simple_uart) using the UART serial viewer built into the Keil programming...
Does anyone know how to get debug messages out to host console via SWD? I know SWD supports Serial Wire Viewer, but not sure how to get it working over GDB with JLink.
...
Hi,
I'm going to try not to get into stuff that is under apple's NDA, but my question is really on the nRF8001 side. Basically, the ANCS is a service that offers three...
I am definitely missing something here, but I can't figure out how to specify a subset of data to read from my peripheral.
Here's the setup: my nrf51822 device is a server...
Hi,
How to create new project for nordic controller using Keil
We are using pca10001 evaluation kit.
Actually in keil i open new project and select nrf51xxx board...
Dear Nordic Developer Zone,
I am trying to enable the readback protection in the main function just before the "wait for interrupt" sd_app_event_wait function using the...
Based on s110 v5.2 release note, nRF51822 will have future hardware revision.
What is the change for future hardware revision? Do we need to modify our circuit design for...
Hi all
My target board is nRF51822 , and I want to run the heart rate demo project,
but a error message when I compile it :
[b]Build target 'nrf51822_xxaa_s110 (256K...
Hi,
Now I want to make a project myself. My project include A/D and BLE for transmiting AD result. But I am confused about what BLE services should I add in my project. and...
Hello all,
I'm stuck in the use of the UART.
I have used the code from the UART example and the UART application for iPhone. I'm using eclipse because I don't want to...
